DELL EMC D-PE-OE-23 Practice Exams
Last updated on Oct 23,2026- Exam Code: D-PE-OE-23
- Exam Name: Dell Technologies PowerEdge Operate 2023
- Certification Provider: DELL EMC
- Latest update: Oct 23,2026
A customer encounters a MEM7114 message indicating the post package repair (PPR) has failed.
What should be the next step to reach a resolution?
- A . Move A side DIMM to B side.
- B . Swap the processors.
- C . Replace affected DIMM.
- D . Reseat affected DIMM.
A technician needs to update the iDRAC license on a PowerEdge R540 from Basic to Enterprise. The server cannot be taken offline but the technician needs to have the additional features of the Enterprise license active as soon as possible.
How can the technician upgrade the license?
- A . The PowerEdge R540 can only be upgraded to iDRAC Express and not iDRAC Enterprise because it is an entry level server
- B . Use the iDRAC GUI to upgrade from Basic to Enterprise
- C . Use the iDRAC GUI to upgrade from Basic to Express, reboot the server and then use the iDRAC GUI to upgrade from Express to Enterprise
- D . Use the Lifecycle Controller, navigate to the Update and Rollback feature and upgrade to Enterprise
What category of error is indicated by HWC8011?
- A . Configuration validation error
- B . Uncorrectable memory error
- C . Voltage irregularity error
- D . Dell diagnostics error
Before deploying a server, a customer needs a technician to configure the front panel LCD to display a custom message that contains the customer’s help desk phone number. However, the server cannot be rebooted.
Where can the technician configure the LCD?
- A . Lifecycle Controller
- B . iDRAC web GUI
- C . System BIOS
- D . iSM
What is a key feature of Part Replacement in Lifecycle Controller?
- A . What is a key feature of Part Replacement in Lifecycle Controller?
- B . Automatically updates the configuration of the new part.
- C . Automatically updates the server configuration database.
- D . Runs a parts replacement wizard.
168.0.120 (/24)
. Gateway: 192.168.0.1
. DNS Server 1: 10.10.0.1
. DNS Server 2: 10.10.0.2
Step-by-Step Guide:
Access iDRAC Network Settings:
Log into the iDRAC interface.
Go to the iDRAC Settings tab in the top menu.
Select Network from the dropdown options. This will open the network configuration page.
Change IP Address and Subnet Mask:
In the Network settings, locate the section for IPv4 Settings.
Set the IP Address to 192.168.0.120.
For the Subnet Mask, since it’s a /24 CIDR, set it to 255.255.255.0.
Configure the Gateway:
In the same section, find the field for Default Gateway.
Enter the Gateway as 192.168.0.1.
Update DNS Server Information:
Scroll down to the DNS Server settings.
Enter DNS Server 1 as 10.10.0.1.
Enter DNS Server 2 as 10.10.0.2.
Apply the Settings:
After entering all the new network information, click on Apply or Save to confirm the changes. The iDRAC interface may prompt for a restart to apply network changes.
Follow any prompts as needed.
Verify the Configuration:
After applying the changes, check that the iDRAC is accessible at the new IP address 192.168.0.120. Confirm that the gateway and DNS settings are properly configured by testing connectivity or accessing the iDRAC from a device within the same network segment.
By completing these steps, you will have reconfigured the iDRAC network settings for the new network segment, allowing remote management of the Dell PowerEdge server at the edge location.
Which LED status indicates that System ID mode is active in a Dell PowerEdge R760 server?
- A . Solid blue
- B . Blinking blue
- C . Solid white
- D . Blinking amber
A technician is working on an operational PowerEdge R640 server that cannot be rebooted. Observing that all drives are hot-swappable devices, the technician decides to remove a drive that has been giving intermittent errors. After the single drive is removed the operating system crashes.
What could have caused the operating system to crash?
- A . iDRAC was not configured for hot-swappable components
- B . System Lockdown mode was enabled, which does not allow any component to be hot-swapped
- C . Drive was part of a RAID 0 virtual disk
- D . PERC was configured to allow a single drive removal
A technician needs to roll back the firmware on a server for the Fiber Channel card. The technician needs to determine the previous version before rolling back the firmware.
How should the technician view the previous and current firmware versions utilizing Lifecycle Controller?
- A . Under Firmware Update, select Launch Firmware Rollback and select Components
- B . Under Hardware Configuration, select Launch Firmware Rollback and select Components
- C . Under Firmware Update, select View Current Versions
- D . Under Hardware Configuration, select View Current Versions
A technician needs to roll back the firmware on a server for the Fiber Channel card. The technician needs to determine the previous version before rolling back the firmware.
How should the technician view the previous and current firmware versions utilizing Lifecycle Controller?
- A . Under Firmware Update, select Launch Firmware Rollback and select Components
- B . Under Hardware Configuration, select Launch Firmware Rollback and select Components
- C . Under Firmware Update, select View Current Versions
- D . Under Hardware Configuration, select View Current Versions