DELL EMC D-PCM-DY-23 Practice Exams
Last updated on Nov 16,2026- Exam Code: D-PCM-DY-23
- Exam Name: Dell PowerSwitch Campus Deploy 2023
- Certification Provider: DELL EMC
- Latest update: Nov 16,2026
The exhibit represents a topology with all Dell EMC N4000 Series switches with RSTP enabled. In addition, the switches are using the default configuration on all ports and protocols.

Which port number will be blocked by spanning tree?
- A . Te 1/0/3
- B . Te 1/0/4
- C . Te 1/0/5
- D . Te 1/0/6
Which function does a VRRP backup router perform?
- A . Sends keepalive advertisements to the other backup routers
- B . Processes and responds to ARP requests
- C . Forwards packets to the Master with a destination IP of the virtual IP address
- D . Receives packets with the virtual MAC address as the destination for other backup routers
Which two are other names for the Backbone Area? (Select 2)
- A . Area 0.0.0.0
- B . Area 255
- C . Area 255.255.255.255
- D . Area 0
After setting up the VoIP configuration, a network administrator issues the following commands with the results shown:
– console# show voice vlan Administrative
– Mode………………………Enable
– console# show voice vlan it gi 1/0/2
– Interface………………………………….Gi1/0/2
– Voice VLAN Interface Mode……………Enabled
– Voice VLAN ID………………………….10
– Voice VLAN COS Overwrite……………False
– Voice VLAN DSCP Value……………….46
– Voice VLAN Port Status…………………Enabled
– Voice VLAN Authentication…………….Disabled
Based on this information, what is the Layer 3 QoS value?
- A . 5
- B . 10
- C . 46
- D . Gi1/0/2
What is the typical sequence of steps to upgrade the firmware of a Dell EMC N-Series switch?


Which interface on a Dell EMC N-Series switch provides the most security for management?
- A . VLAN
- B . Ethernet
- C . Loopback
- D . Out-of-band
You are tasked with deploying a single Dell EMC N-Series switch with a 2-port port-channel to uplink to an existing upstream switch.
The following reflects the upstream switch configuration:
– N4032F#show running-config interface tengigabitethernet 1/0/5 channel-group 1 mode on
– N4032F#show running-config interface tengigabitethernet 1/0/6 channel-group 1 mode on
Which type of port-channel should be configured to successfully uplink?
- A . Active
- B . MLAG
- C . Static
- D . Passive
Which username and password authentication methods do Dell EMC Campus networking switches support?
- A . radius, local, ias
- B . line, local, radius
- C . ias, line, radius
- D . local, line, ias
Which two centralized authentication and authorization methods are available for Dell PowerSwitches? (Select 2)
- A . RADIUS
- B . Active Directory
- C . TACACS
- D . LDAP
A network administrator has configured a 4-port port-channel between two Dell EMC Campus networking switches. The physical interfaces show as administratively up and operationally up on both switches. However, the port-channel shows as operationally up on Switch A and operationally down on Switch B.
What is a potential reason for the inconsistent port-channel state?
- A . Switch A is configured to use dynamic port-channels and Switch B is configured to use static port- channels
- B . Ports in the port-channel on Switch A are all the same speed but the ports in the port- channel on Switch B are a mix of speeds
- C . Switch A is configured using channel-group # mode on and Switch B is configured using channel- group # mode auto
- D . N-Series supports a maximum number of physical interfaces that can be included in port-channels on a per-device basis