Cisco 300-620 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-620
- Exam Name: Implementing Cisco Application Centric Infrastructure (DCACI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
A Solutions Architect is asked to design two data centers based on Cisco ACI technology that can extend L2/L3, VXLAN, and network policy across locations. ACI Multi-Pod has been selected.
Which two requirements must be considered in this design? (Choose two.)
- A . ACI underlay protocols, i.e. COOP, IS-IS and MP-BGP, spans across pods. Create QoS policies to make sure those protocols have higher priority.
- B . A single APIC Cluster is required in a Multi-Pod design. It is important to place the APIC Controllers in different locations in order to maximize redundancy and reliability.
- C . ACI Multi-Pod requires an IP Network supporting PIM-Bidir.
- D . ACI Multi-Pod does not support Firewall Clusters across Pods. Firewall Clusters should always be local.
- E . Multi-Pod requires multiple APIC Controller Clusters, one per pod. Make sure those clusters can communicate to each other through a highly available connection.
B, C
Explanation:
When designing two data centers based on Cisco ACI technology that can extend L2/L3, VXLAN, and network policy across locations with ACI Multi-Pod, the two requirements that must be considered are:
A single APIC Cluster is required in a Multi-Pod design4.
ACI Multi-Pod requires an IP Network supporting PIM-Bidir2.
Upgrade the spine switches to the targeted release.
Explanation:
When upgrading the Cisco ACI fabric through an intermediate release, the following steps should be taken:
Upgrade the APICs to an interim release: This is the first step to ensure that the APICs are running a stable version that is compatible with both the current and the targeted release1.
Upgrade the switches to an interim release: After the APICs are upgraded, the next step is to upgrade the leaf and spine switches to the same interim release. This ensures that the entire fabric is running on a compatible version before moving to the targeted release1.
Upgrade the APICs to the targeted release: Once the fabric is stable on the interim release, the APICs can be upgraded to the targeted release. It’s important to verify that the APICs are fully operational before proceeding to upgrade the switches1.
Upgrade the leaf and spine switches to the targeted release: The final step is to upgrade the leaf and spine switches to the targeted release. This should be done after the APICs have been successfully upgraded and are stable on the targeted release1.
By following these steps, the customer can successfully upgrade the Cisco ACI fabric to the new code release that includes the desired feature.
An engineer must perform a Cisco ACI fabric upgrade that minimizes the impact on user traffic and allows only permitted users to perform an upgrade.
Which two configuration steps should be taken to meet these requirements?
- A . Divide Cisco APIC controllers into two or more maintenance groups.
- B . Grant tenant-ext-admin access to a user who performs an upgrade
- C . Combine all switches into an upgrade group.
- D . Divide switches into two or more maintenance groups.
- E . Grant the fabric administrator role to a user who performs an upgrade.
A, D
Explanation:
To perform a Cisco ACI fabric upgrade that minimizes the impact on user traffic and allows only permitted users to perform an upgrade, the following configuration steps should be taken:
Divide Cisco APIC controllers into two or more maintenance groups: This step involves organizing the APIC controllers into separate maintenance groups to allow for a phased upgrade process, reducing the impact on user traffic5.
Divide switches into two or more maintenance groups: This step involves organizing the switches into separate maintenance groups, which allows for a controlled and phased upgrade process, minimizing
the impact on the network during the upgrade5.
Reference: https://www.cisco.com/c/en/us/td/docs/dcn/whitepapers/cisco-application-centric-infrastructure-design-guide.html
A Cisco ACI fabric is integrated with a Cisco ASA firewall using a service graph under the tenant called Operations. The fabric must permit the firewall used on tenant Operations to be referenced by the tenant called Management.
Which export action must be used to accomplish this goal?
- A . Layer4-Layer7 device
- B . router configurations
- C . service graph template
- D . device selection policies
A
Explanation:
In Cisco ACI, when a service graph is deployed under one tenant (e.g., Operations) and needs to be referenced by another tenant (e.g., Management), the Layer 4-Layer 7 (L4-L7) device export action is used. This allows the firewall or other L4-L7 devices defined in the service graph to be shared across tenants. By exporting the L4-L7 device, the configuration enables the Management tenant to reference and use the firewall deployed in the Operations tenant.
A Cisco ACI fabric is integrated with a Cisco ASA firewall using a service graph under the tenant called Operations. The fabric must permit the firewall used on tenant Operations to be referenced by the tenant called Management.
Which export action must be used to accomplish this goal?
- A . Layer4-Layer7 device
- B . router configurations
- C . service graph template
- D . device selection policies
A
Explanation:
In Cisco ACI, when a service graph is deployed under one tenant (e.g., Operations) and needs to be referenced by another tenant (e.g., Management), the Layer 4-Layer 7 (L4-L7) device export action is used. This allows the firewall or other L4-L7 devices defined in the service graph to be shared across tenants. By exporting the L4-L7 device, the configuration enables the Management tenant to reference and use the firewall deployed in the Operations tenant.
Where is the COOP database located?
- A . leaf
- B . spine
- C . APIC
- D . endpoint
B
Explanation:
The COOP (Council Of Oracle Protocol) database is located on each spine switch within the Cisco ACI fabric. The COOP database is responsible for maintaining a consistent copy of endpoint address and location information across the fabric
Reference: https://www.cisco.com/c/en/us/solutions/collateral/data-center-virtualization/application-centric- infrastructure/white-paper-c11-739989.html
A Cisco ACI endpoint group must have its gateway address migrated out of the ACI fabric. An engineer configures EPG-TEST with a static port binding and configures the encap VLAN with the required VLAN.
Which configuration set must be used on the bridge domain to meet these requirements?
- A . L2 Unknown Unicast: Hardware Proxy
Unicast Routing: Disabled
ARP Flooding: Enabled - B . L2 Unknown Unicast: Hardware Proxy
Unicast Routing: Disabled
ARP Flooding: Disabled - C . L2 Unknown Unicast: Flood
Unicast Routing: Disabled
ARP Flooding: Enabled - D . L2 Unknown Unicast: Flood
Unicast Routing: Enabled
ARP Flooding: Enabled
A
Explanation:
To migrate the gateway address out of the ACI fabric for an endpoint group (EPG), the bridge domain configuration must ensure that routing is contained within the ACI fabric and that ARP requests are managed efficiently.
The correct configuration set is:
L2 Unknown Unicast: Set to Hardware Proxy. This setting allows the ACI fabric to use the spine proxy function to handle unknown unicast traffic, which helps to reduce flooding within the fabric.
Unicast Routing: Set to Disabled. Since the gateway is being migrated out of the ACI fabric, unicast routing should be disabled to prevent the ACI fabric from attempting to route traffic for the EPG.
ARP Flooding: Set to Enabled. This allows ARP requests to be flooded within the bridge domain, which is necessary when the unicast routing is disabled, to ensure that ARP requests can still be resolved.
Reference: Cisco ACI Bridge Domain Configuration Guide
Cisco ACI Best Practices Guide
An engineer must advertise a bridge domain subnet out of the ACI fabric to an OSPF neighbor.
Which two configuration steps are required? (Choose two.)
- A . Configure Subnet scope to Advertised Externally
- B . Add External Subnet for External EPG flag under External EPG.
- C . Create Route Control Profile with the export direction under External EPG.
- D . Add L30ut profile to the bridge domain using Associated L30uts section
- E . Configure the Subnet under the EPG level.
A, D
Explanation:
To advertise a bridge domain subnet out of the ACI fabric to an OSPF neighbor, the following configuration steps are required:
Configure Subnet scope to Advertised Externally: This step involves setting the scope of the subnet within the bridge domain to be advertised externally, which allows the subnet to be propagated to external routing entities3.
Add L30ut profile to the bridge domain using Associated L30uts section: This step involves associating the bridge domain with an L3Out profile, which is necessary for the bridge domain subnet to be advertised to OSPF neighbors4.
In-band is currently configured and used to manage the Cisco ACI fabric. The requirement is for leaf and spine switches to use out-of-band management for NTP protocol.
Which action accomplishes this goal?
- A . Select Out-of-Band as Management EPG in the default DateTimePolicy.
- B . Create an Override Policy with NTP Out-of-Band for leaf and spine switches.
- C . Change the interface used for APIC external connectivity to ooband.
- D . Add a new filter to the utilized Out-of-Band-Contract to allow NTP protocol.
B
Explanation:
To configure leaf and spine switches in a Cisco ACI fabric to use out-of-band management for NTP protocol, an Override Policy with NTP Out-of-Band must be created. This policy specifies that NTP traffic should be directed through the out-of-band management network, separate from the in-band management traffic, ensuring dedicated management connectivity for time synchronization.
https://www.cisco.com/c/en/us/support/docs/cloud-systems-management/application-policy-infrastructure-controller-apic/200128-Configuring-NTP-in-ACI-Fabric-Solution.html
What two actions should be taken to deploy a new Cisco ACI Multi-Pod setup? (Choose two.)
- A . Configure MP-BGP on IPN routers that face the Cisco ACI spines.
- B . Connect all spines to the IPN.
- C . Configure anycast RP for the underlying multicast protocol
- D . Configure the TEP pool of the new pod to be routable across the IPN.
- E . Increase interface MTU for all IPN routers to support VXLAN traffic.
D, E
Explanation:
When deploying a new Cisco ACI Multi-Pod setup, it’s crucial to ensure that the Tunnel Endpoint (TEP) pool of the new pod is routable across the Inter-Pod Network (IPN). This allows the TEP addresses to be reachable across the pods, facilitating communication between them. Additionally, increasing the Maximum Transmission Unit (MTU) for all IPN routers is necessary to support the larger frame size required by VXLAN encapsulation, which is typically above the standard Ethernet MTU of 1500 bytes.
Reference: Cisco ACI Multi-Pod Configuration Guide
Cisco ACI Best Practices Guide