Cisco 300-510 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-510
- Exam Name: Implementing Cisco Service Provider Advanced Routing Solutions (SPRI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
What is the purpose of ACL type prefix set entries in RPL prefix sets?
- A . They hold IPv4 or IPv6 prefixes that do not match specifications.
- B . They hold IPv4 or IPv6 prefix match specifications.
- C . They hold IPv6 prefix match specifications.
- D . They hold IPv4 prefixes that do not match specifications.
Refer to the exhibit.

An MPLS core network has connectivity issues R4 has failed. It impacts traffic loss between R1 and R8. Customers report no access to their file servers, which delays their transformation work.
Which quick action resolves the issue until R4 recovers?
- A . Implement Link and Node protection on routers R2 and R7.
- B . Disable traffic engineering so that traffic prefers the IGP path
- C . Enable MPLS TE fast reroute on router R1 and Link and Node protection on router R2.
- D . Configure IBGP full mesh for faster convergence.
Which task is performed when troubleshooting LDP?
- A . Execute the ping utility to generate information about the MAC addresses used along the path
- B . Verify that MPLS is disabled globally and enabled on the necessary interfaces in a per-interface basis
- C . Execute the traceroute utility to generate information about the labels used along the path
- D . Verify that Cisco Express Forwarding has been disabled on the network
Refer to the exhibit.

MPLS traffic from the packet core that is connected to router RX (10 10 101) to the radio network that is connected to router RB (10 10 10 6) uses the longer route RB R2 RY RX RX and R2 are configured with a default value of LDP hello and hold intervals The team verified that OSPF neighborship in Area 0 is established between RX and R2.
Which action must be taken to choose the shortest path and resolve the issue?
A)
![]()
B)
![]()
C)
![]()
D)
![]()
- A . Option A
- B . Option B
- C . Option C
- D . Option D
What is used by SR-TE to steer traffic through the network?
- A . shortest path calculated by IGP
- B . dynamic rules
- C . path policy
- D . explicit maps
C
Explanation:
Reference: https://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/segment-routing/configuration/guide/b-seg-routing-cg-asr9k/b-seg-routing-cg-asr9k_chapter_0100.html
Refer to the exhibit.

AJI four routers on the network reside in the same data center The four routers are running IS-IS between them in Level 1 mode within an IPv4 network After a network engineer installed several new servers connected to R4, users connected via R1 reported they could not connect to applications on the servers The engineer has determined that R4 is receiving routes from R3 but it is failing to receive routes from R1.
Which action must the engineer take to resolve the issue?
- A . Configure R3 only lo be a Level 1’Level 2 router.
- B . Configure R2 and R3 to be Level 1/Level 2 routers
- C . Configure R2 only to be a Level 2 router
- D . Configure R1 and R4 to be Level 2 routers
The ISP_A network is configured with PIMv2 with sparse mode. The engineering team at ISP_A must implement multicast support following RFC 5059 in the network. The RP priority will be 0, and the solution must require limited supervision from the operations team.
Which action must the team take to meet the requirements?
- A . Implement Auto-RP on the candidate RP and the mapping agent only.
- B . Implement Static RP across all routers in the network.
- C . Implement bootstrap router in the network core.
- D . Implement Anycast-RP on edge routers only.
Refer to the exhibit.

Refer to the exhibit. Routers CE1 and CE2 are in AS 65530. which is multihomed for Internet access. An engineer expects inbound traffic to AS 65530 to arrive from PE1. but it is coming from PE2 instead PE1 and PE2 routers are connected with CE routers through the same bandwidth.
Which action must be taken to correct the problem?
- A . On router CE2, configure inbound routes from PE2 to CE2 with a local-preference value of 50 or greater.
- B . Configure router CEI to prepend the AS path to routes it receives from PE 1.
- C . Set the local-preference value on router CEI to 100 or greater
- D . On router PEI, change the origin for routes that are redistributed from CEI to CE2.
Refer to the exhibit.

R21 is a multicast source sending multicast traffic 224.1.1.1 to R23, with RP22 serving as the rendezvous point inside AS65222. A network engineer noticed that when R21 goes down, R12 in AS65111 starts to send the same multicast group 224.1.1.1 through RP11.
Which action resolves the issue?
- A . Block service groups 224.0.1.39 and 224.0.1.40 between the two autonomous systems
- B . Disable PIM parse mode between RP11 and RP22 in the two autonomous systems.
- C . Advertise RP2 with a high local preference in AS65222.
- D . Enable passive interface under EIGRP between the two autonomous systems.
Refer to the exhibit.

A network engineer applied configuration on R5 to summarize all OSPF routes, but R4 is still receiving specific routes from R5. The engineer has confirmed that both R5 and R4 routers are configured with correct summarization configuration but R5 Is not sending the summary routes.
What action must the engineer take to fix the problem?
- A . Remove summarization configuration on R5 and configure it on R4
- B . Configure a sham link between R4 and R5 to support summarization within Area 2
- C . Move R4 and R5 in separate areas as now they maintain the same link-state database
- D . Clear link-state database on both R4 and R5 routers for summarization to work