Cisco 300-510 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-510
- Exam Name: Implementing Cisco Service Provider Advanced Routing Solutions (SPRI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
A network engineer is troubleshooting OSPF multiare A.
Which Cisco IOS XR feature should the engineer use in order to streamline OSPF issue?
- A . hierarchical CLI
- B . DR support for topology management
- C . routing process enabled by default on all interfaces
- D . show ip ospf topology command
A
Explanation:
OSPF Hierarchical CLI and CLI Inheritance
Hierarchical CLI is the grouping of related network component information at defined hierarchical levels such as at the router, area, and interface levels. Hierarchical CLI allows for easier configuration, maintenance, and troubleshooting of OSPF configurations. When configuration commands are displayed together in their hierarchical context, visual inspections are simplified. Hierarchical CLI is intrinsic for CLI inheritance to be supported.
With CLI inheritance support, you need not explicitly configure a parameter for an area or interface. In the software, the parameters of interfaces in the same area can be exclusively configured with a single command, or parameter values can be inherited from a higher hierarchical level―such as from the area configuration level or the router ospf configuration levels.
More information: https://www.cisco.com/c/en/us/td/docs/iosxr/ncs5500/routing/71x/b-routing-cg-ncs5500-71x/b-routing-cg-ncs5500-71x_chapter_011.html#con_1059437
Reference: https://www.cisco.com/c/en/us/td/docs/routers/xr12000/software/xr12k_r4-0/routing/configuration/
guide/rc40xr12k_chapter4.html#con_1059437
Refer to the exhibit.

Router 1 and Router2 have shared routes in the OSPF database but the routes are missing from their routing tables. Checking me prefix-list configuration on both routers, the engineer confirmed all networks are allowed.
What action should the engineer take to fa the problem?
- A . Configure the two routers with different process IDs
- B . Configure the two routers with different hello and dead timer values
- C . Switch the DR and BDR roles between the two routers
- D . Configure interface Senal1/0 on Router1 as a point-to-point interface
Refer to the exhibit

Router R1 is configured to advertise outgoing SA messages to routers R2 and R3, but to receive incoming SA messages only from R2.
Which additional configuration must an engineer apply to router R1 so it filters all MSDP SA messages from Domain-C?
- A . R1# ip msdp sa-filter in 192.168.3.1
- B . R3# ip msdp sa-filter out 192.168.3.1
- C . R3# ip msdp password peer 192.168.1.1
- D . R1# ip msdp password peer 192.168.3.1
A
Explanation:
Reference: https://www.cisco.com/c/en/us/support/docs/ip/ip-multicast/13717-49.html
Refer to the exhibit.

An administrator is troubleshooting Internet access issues on a customer’s network. After applying this ISIS configuration to R1, the administrator notices that it fails to redistribute the default route into IS-IS. After checking the connectivity between the ISIS router and the ISP router the engineer confirmed there is Layer 3 connectivity between them.
Which action should be taken to correct the problem?
- A . Associate the default route with a VRF
- B . Add the default-information originate command to the configuration
- C . Configure the default route under any routing protocol other than IS-IS
- D . Configure R1 as a Layer 1 router
Which command is used to enable BIDIR-PIM under global configuration mode for Cisco IOS XE Sofware?
- A . ip pim bidir-enable
- B . ipv4 pim bidir-enable
- C . ip multicast-routing
- D . ip pim bidir
A
Explanation:
Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipmulti_pim/configuration/xe-3s/imc-pim-xe-3sbook/imc_basic_cfg.html
Refer to the exhibit.

OSPF is running in the core of a company. Router RA is running EIGRP. After the company acquired an additional office, an engineering team connected the two networks from router RA to router R1. OSPF and EIGRP have been mutually redistributed on R1. but the team cannot view the routes on R3.
Which action must the team take to resolve the issue?
- A . Create a virtual link between R1 and R2.
- B . Configure the routers in Area 2 to be in Area 0.
- C . Disable stub routing in Area 1.
- D . Redistribute connected routes on R3.
Which expression, when used with the as-path-set command, matches the AS path attribute of the route?
- A . neighbor-is
- B . dfa-regtex
- C . ios-regex
- D . Length
Refer to the exhibit Dedicated MPLS Layer 3 services for VRF customer A are configured on the MPLS network for FTP access OSPF with area 0 configuration is used as the interior routing protocol between the routers, and LDP is up and running on the MPLS network. After recent maintenance work on the MPLS network. IP address 172.16 100 1 cannot access the FTP server with IP address 172.16 192.21 All loopbacks are reachable on the network.
Which configuration must the engineer apply to correct the problem?
- A . Configure passive-interface under the Gi0/2 interface on R22
- B . Configure ip ospf network point-to-point under the Lo0 interface on R33
- C . Configure network 33.33.10.1 0.0.0.255 area 0 under the OSPF configuration on R33
- D . Configure ip cef under the global configuration on R22
What is the difference between RPL and route map actions?
- A . RPL uses match, pass, set, and drop actions, and route maps use match, set. and drop actions.
- B . RPL uses pass. set. and drop actions only, and route maps use match, set, and drop actions.
- C . RPL uses pass, set. drop, and done actions, and route maps use match and set actions only.
- D . RPL uses match, set, drop, and stop actions, and route maps use match, set, and drop actions.
Refer to the exhibit.

Routers RA and RB are IS-IS peers configured for NSF but router RC is an IS-IS peer without NSF capability
If RA undergoes processor switchover what is the effect on the network environment?
- A . If RC is operating without the Cisco configuration option all three routers tear down their peering relationships and re-establish peering
- B . All peer relationships remain up and the link-state database is unchanged
- C . All peer relationships remain up, but the link-state database is rebuilt on each device
- D . If RC is operating without the Cisco configuration option only 2 routers tear down their peering relationships and re-establish peering