Cisco 300-510 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-510
- Exam Name: Implementing Cisco Service Provider Advanced Routing Solutions (SPRI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
Refer to the exhibit.

The initial BGP configuration of the network is complete, and all the routers have established BGP neighborship. The engineer configured Router 2 with additional BGP paths to install and advertise more paths to Router 1 and Router 3.
Which configuration must the engineer apply to Router 1 and Router 3 so that they will use and install all additional paths?

- A . Option A
- B . Option B
- C . Option C
- D . Option D
Refer to the exhibit.

After you applied these configurations to routers R1 and R2, the two devices could not form a neighbor relationship.
Which reason for the problem is the most likely?
- A . The two routers cannot authenticate with one another.
- B . The two routers have the same area ID.
- C . The two routers have the same network ID.
- D . The two routers have different IS-types.
C
Explanation:
For those asking about the password, area authentication doesn’t prevent neighboring to come up because it is carried only in LSP, CSNP and PSNP messages and not in IIH messages. https://www.cisco.com/c/en/us/support/docs/ip/integrated-intermediate-system-to-intermediate-system-is-is/13792-isis-authent.html
DRAG DROP
Drag and drop the features about multicast from the left onto the multicast protocols on the right.
Not all options ate used.


Refer to the exhibit.

The green policy is designed with low delay, and the pink policy is designed with low cost.
What is the next hop for node A on its way to node D, with the objective of achieving a low delay?
- A . 192.168.3.2
- B . 192.168.1.6
- C . 192.168.3.6
- D . 192. 168.1.2
Refer to the exhibit.

The green policy is designed with low delay, and the pink policy is designed with low cost.
What is the next hop for node A on its way to node D, with the objective of achieving a low delay?
- A . 192.168.3.2
- B . 192.168.1.6
- C . 192.168.3.6
- D . 192. 168.1.2
Which statement about BFD on Cisco IOS XR Software is true?
- A . Cisco IOS XR router must use LDP to route back to the Cisco IOS router to establish the peer relationship.
- B . Cisco IOS XR Software does not support BFD multihop for IPv4.
- C . Cisco IOS XR router must use dynamic routing or a static route back to the Cisco IOS router to establish the peer relationship.
- D . BFD is not compatible between Cisco IOS XR and Cisco IOS Software.
C
Explanation:
A router running BFD in Cisco IOS software can designate a router running BFD in Cisco IOS XR software as its peer using the bfd neighbor command; the Cisco IOS XR router must use dynamic routing or a static route back to the Cisco IOS router to establish the peer relationship. https://www.cisco.com/c/en/us/td/docs/routers/crs/software/crs_r6-1/routing/configuration/guide/b-routing-cg-crs-61x/b-routing-cg-crs-61x_chapter_0100.html
Reference: https://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/asr9k-r6-3/routing/configuration/
guide/b-routing-cg-asr9000-63x/b-routing-cg-asr9000-63x_chapter_0100.html
Refer to the exhibit.

Excessive routes are flooding from network 150.0.0.0 into AS100. Internet traffic between AS400 and AS300 is working normally. No route controlling mechanism is applied on incoming and outgoing traffic.
Which configuration resolves the issue?

- A . Option A
- B . Option B
- C . Option C
- D . Option D
DRAG DROP
Drag and drop the route-manipulation methods from the left onto their features on the right

Explanation:
As-path filter C It uses regular expressions to filter traffic
Route-map C It matches packets with specified criteria and performs configured actions against them
Distribute list C if filters routes into and out of routing protocols
Offset-list C It converts incoming and outgoing metrics on RIP and EIGRP route
Refer to the exhibit.

A network engineer must enable segment routing between the three autonomous systems with these requirements:
・ OSPF link-state data for area 0 routers must be distributed to the controller via BGP LS.
・ EPE must be enabled on the egress node in AS 100.
・ Routers must advertise peer node SIDs to the controller R1 via BGP LS.
Which configuration must the engineer apply?
A)

B)

C)

D)

- A . Option A
- B . Option B
- C . Option C
- D . Option D
Refer to the exhibit.

An engineer at a large ISP is troubleshooting suboptimal routing on a customer’s IS-IS network with multiple Level 1-2 routers. The network consists of numerous routers that are configured for MPLS. When IS-IS picks the closest Level 1-2 router to exit the area, suboptimal routing occurs in Area 8 and Area 10. The other IGP protocols are running correctly, and the IS-IS adjacency between routers is established.
Which action resolves the issue?
- A . Configure each interface as either Level 1 or Level 2 circuit type on router 1.
- B . Configure the router as DIS for each of the interfaces on router 1.
- C . Redistribute Level 2 prefixes into Level 1 on router 2.
- D . Disable advertisement of the default route on router 2.