Cisco 300-510 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-510
- Exam Name: Implementing Cisco Service Provider Advanced Routing Solutions (SPRI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
Refer to the exhibit.

Why is neighbor 10.1.5.5 stuck in “2WAY” state?
- A . Router ID 10.1.5.5 is not reachable from R2
- B . OSPF authentication has failed between R2 and 10.1.5.5
- C . It is an expected behavior when OSPF network type is broadcast
- D . OSPF parameters (Area ID or hello interval) are mismatched between R2 and 10.1.5.5
C
Explanation:
Reference: https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/13683-11.html
Refer to the exhibit.

Why is neighbor 10.1.5.5 stuck in “2WAY” state?
- A . Router ID 10.1.5.5 is not reachable from R2
- B . OSPF authentication has failed between R2 and 10.1.5.5
- C . It is an expected behavior when OSPF network type is broadcast
- D . OSPF parameters (Area ID or hello interval) are mismatched between R2 and 10.1.5.5
C
Explanation:
Reference: https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/13683-11.html
Refer to the exhibit.

Router 1 resides in a different data center than Router 2 and Router 3. Router 1 is running the IS-IS routing protocol, and it is preconfigured with LDP and segment routing.
Which configuration must the engineer apply under router isis 111 on Router 1 to implement Tl-LFA on the link to Router 2 without disrupting traffic to Router 3?
A)

B)
![]()
C)
![]()
D)

- A . Option A
- B . Option B
- C . Option C
- D . Option D
Refer to the exhibit.

All routers in the network are in area 12. with IS-IS running in the default configuration as the IGP To avoid congestion on the link from R1 to R2 the network architect planned for traffic from R1 to R3 to pass through R4 To meet the requirement a network engineer set the metric from R1 to R4 to a cost of 15 but the traffic is still travelling through R2.
Which action must the engineer take to resolve the issue?
- A . Change the default metric to 20 on all links and disable wide area metrics
- B . Change the cost on the link from R1 to R2 to 11 and enable narrow metrics
- C . Change the cost on the link from R1 to R4 to 5
- D . Change the IS-IS administrative distance to 10
Refer to the exhibit.

Network connectivity between bank A and bank B has been lost Users at bank A and bank B are able to successfully reach their directly connected PE routers. All routers in OSPF area 0 are correctly advertising and learning routing updates.
Which action resolves the issue?
- A . Enable next-hop-self under the iBGP peering configuration on routers PEI and PE2
- B . Configure the P routers to redtstnbute BGP routes within OSPF area 0.
- C . Configure router PI to advertise the IP prefix of PEI.
- D . Configure MPLS with an end-to-end label-switched path on each router.
What is a requirement of PIM-SM?
- A . It requires Cisco Express Forwarding to be enabled.
- B . It must be enabled on loopback interfaces only
- C . It requires OSPF to be configured on the network.
- D . It must use an RP
For which reason can two BGP peers fail to establish a neighbor relationship?
- A . Their BGP send-community strings are misconfigured
- B . Their BGP timers are mismatched
- C . Their remote-as numbers are misconfigured
- D . They are both activated under an IPv4 address family
Refer to the exhibit.

After these configurations were applied to routers R1 and R2. the two devices cannot form a neighbor relationship
What is the reason for the problem?
- A . The two routers have the same area ID.
- B . The two routers have different iS-types
- C . The two routers have the same network ID
- D . The two routers cannot authenticate with one another
Refer to the exhibit.

ISP_A in AS 635 has four BGP neighbors connected one-by-one, starting from AS 12 R1 has been configured with bgp deterministic-med and bgp additional-paths install to influence egress traffic After a recent reload of R10, all traffic was automatically re-routed via AS 87 A network engineer must correct the traffic flow and route the traffic via AS 101.
Which configuration must the engineer apply to R1 to correct the problem without affecting the second BGP attribute?
- A . bgp bestpath compare-routerid
- B . bgp bestpath med missing-as-worst
- C . bgp always-compare-med
- D . bgp default local-preference 200
After you change the IP address on an IOS XR router, you cannot ping the new address.
Which step did you forget to complete?
- A . commit the configuration
- B . roll back the configuration
- C . merge the configuration
- D . save the running configuration