Cisco 300-510 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-510
- Exam Name: Implementing Cisco Service Provider Advanced Routing Solutions (SPRI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
The engineering team at ISP_1 must improve network stability time and minimize the impact of routing instabilities from other domains to unicast transit services in the backbone R1 is part of an OSPF- enabled network, and acts as an ASBR connected via interface Gi0/1 to the external domain. The OSPF exponential backoff algorithm RFC 3623 with helper mode is already implemented on R1.
Which additional configuration must the ISP_1 team apply to suppress routing instability for 3 minutes?
- A . Configure ip ospf resync-timtout 180 under the Gi0’1 interface configuration
- B . Configure ip ospf timer nsf interval 3 under the global Gi0’1 interface configuration
- C . Configure nsf ittf restart-inttrval 180 under the global OSPF configuration
- D . Configure nsf ospf wait 3 under the global OSPF configuration
DRAG DROP
An engineer is troubleshooting end-to-end customer traffic across an MPLS VPN service provider network.
Which tasks should the engineer use to solve the routing issues? Drag and drop the table types from the left onto the most useful troubleshooting tasks/router types on the right. (Not all options are used.)


Refer to the exhibit.


MPLS traffic from 192.168.4.0/24 to 192.168.5.0/24 is failing to pass over the link from R4 to R2.
The engineer verified that:
✑ Cisco Express Forwarding Is enabled on all routers.
✑ All routers reach all networks via OSPF.
✑ MPLS traffic from 192.168.1.0/24 to 192.168.3.0/24 is passing normally over the link from R1 to R2.
Which action resolves the issue?
- A . On router R4, remove the mpls ip command on the s/O/O/2 interface.
- B . On router R2, configure the mpls ip command on the SIO/O/4 interface.
- C . On router R4, configure the mpls label protocol Idp command on all serial interfaces.
- D . On router R2, configure the mpls label protocol Idp command on the interface.
Refer to the exhibit.

XR1 and XR2 are sending the prefix 10.11.11.0/24 to XR3. A configured policy on XR1 is incorrectly prepending AS path 11 11 12 12 onto this prefix. A network operator wants to add a policy onto XR3 that will not allow the falsely prepending prefix from being installed.
Which policy configuration applied to the XR3 neighbor configuration for XR1 can accomplish this requirement without impact to other or future received routes?
A)

B)

C)

D)

- A . Option A
- B . Option B
- C . Option C
- D . Option D
D
Explanation:
Reference: https://www.cisco.com/c/en/us/td/docs/routers/crs/software/crs_r4-1/routing/command/reference/b_routing_cr41crs/b_routing_cr41crs_chapter_01000.html#wp3850885229
Refer io the exhibit.

While applying the configurations on two routers an engineer notices that OSPF adjacency Between them remains down Through the ping test the engineer confirmed that both me routers have Layer 3 reachability between them.
Which action should me engineer take to make the adjacencies to full?
- A . Enter the command ip ospf authentication in R2 interface
- B . Enable OSPF just inside the router OSPF process not in the interfaces of any router
- C . Delete the area 0 authentication message-digest command from the OSPF process in R1
- D . Delete the area 0 authentication message-digest command from the OSPF process in R2
Refer to the exhibit.

A network engineer is investigating a report of packet drops in an application running on a server connected to PE2.
The engineer determined that:
– The OSPF adjacency in area 0 is up. and it is learning the loopback addresses of all routers in area 0.
– Traffic from users connected to PE1 to the application is also passing normally.
– Packets from PE2 back to PE1 are being dropped
Which action resolves the issue?

- A . Option A
- B . Option B
- C . Option C
- D . Option D
What does conditional matching operate with RPL?
- A . The matching identifies a group of routes that are removed from the routing table when the administrator defined tags match
- B . The matching identifies tags that are placed on routes from neighboring autonomous systems and drops the routes if they are the same.
- C . The matching identifies a set of criteria, and an action is taken based on whether the criteria are the same or different
- D . The matching identifies interfaces that run the same routing protocol and manipulates data based on the routing rules
Refer to the exhibit.

What is the effect of this configuration?
- A . It sets the keepalive timer to 30 milliseconds and the hold timer to 240 milliseconds.
- B . It sets the keepalive timer to 30 seconds and the hold timer to 240 seconds.
- C . It sets the hold timer to 30 milliseconds and the keepalive timer to 240 milliseconds.
- D . It sets the hold timer to 30 seconds and the keepalive timer to 240 seconds.
Refer to the exhibit.

IS-IS runs in the network and all routers are in the same area R1 statically routes to distribute traffic with R6 and the networking team has redistributed the static routes on R1 into IS-IS Hosts on R3 need access to servers connected to R6 A tag has been applied to the routes to manipulate routes
along the path but routers running IS-IS are still unable to reach the redistributed routes Which action must the team take to resolve the issue?
- A . Configure the routers as Level 1/Level 2 routers
- B . Configure R3 with a default route that uses R2 as the next hop
- C . Configure the IS-IS routers with metric-style wide
- D . Configure the route map with an additional route-map set-tag permit 10 sequence
Which type of BGP attribute does a route reflector attach to routes learned from iBGP peers that allows them to be accepted by other iBGP peers, thereby eliminating the need for a full-mesh BGP topology?
- A . well-known mandatory
- B . optional transitive
- C . well-known discretionary
- D . optional non transitive