Cisco 300-510 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-510
- Exam Name: Implementing Cisco Service Provider Advanced Routing Solutions (SPRI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
Refer to the exhibit.

When implementing SRv6, which SID does R2 propagate into area 0 for the prefix 2001:DB8:1:1/128?
- A . 120
- B . 230
- C . 110
- D . 10
What is the function of BGP confederations?
- A . They require routers to use private AS numbers.
- B . They eliminate the need for a fully-meshed internal BGP design.
- C . They enable a single device to distribute a common configuration to its peers
- D . They assign an external BGP router to serve as the route reflector
Refer to the exhibit.

An engineer is troubleshooting connectivity issues on the MPLS core network. A customer connected through R4 cannot reach the OSPF domain on R5. While checking the routing table of R1, the engineer cannot see all the routes from R3 and R5.
Which task must the engineer perform so that R4 is able to reach R5?
- A . Enable OSPF peering and configure route redistribution between routers R4 and R1.
- B . Enable route filtering between routers R1 and R3.
- C . Enable MP-BGP peering on routers R1. R3, R4, and R5.
- D . Enable OSPF on the Area-0 routers and configure MP-BGP between routers R1 and R3.
Refer to the exhibit.

Customer A and customer B are connecting through a service provider network with these requirements
R1 acts as the mapping server to connect 10 0 0.0/30 and 172.16.0.0/30 networks
R1 and R2 are using nondefault SRG8 range to allocate SID.
R2 ads as the mapping client for transient traffic originating from customer A
Which configuration meets the requirements?
- A . Remove allocation of prefix SlDs for 10.0.0.0/30 and 172.16.0.0/30 on R1.
- B . Configure segment-routing prefix-sid-map advertise-local on R1
- C . Allocate prefix SIDs for 10.0.0.0-30 and 172.16 0.0/30 subnets on R2
- D . Configure segment-routing prefix-sid-map advertise-local on R2.
Refer to the exhibit.

A network engineer configured routers R1 and R5 to run in IS-IS Level 1 mode and router R6 to run in
IS-IS Level 2 mode. All other routers are running as Level 1 / Level 2 routers. An engineer expects traffic from R1 to R6 to pass via R2, but IS-IS routing has calculated the best path via R4.
Which action corrects the problem?
- A . Configure all routers as Level 1 routers.
- B . Remove the link metric for the link from router R1 to router R2.
- C . Change the link metric for the link from router R1 to router R2 to 1.
- D . Configure all routers as Level 1 / Level 2 routers.
C
Explanation:
The default link metric for IS-IS is 10, so changing the link from R1 to R2 to 1 will change the overall metric to R6 to 9 (8+1).
Which lag command is used within route-map to redistribute routes that match with routes tagged with the specified tag numbers?
- A . match routing tag
- B . match all tag
- C . match route tag
- D . match tag
DRAG DROP
Drag and drop the attributes for the BGP route selection on the left into the correct order on the right. Not all options are used.

Explanation:
Reference: https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/13753-25.html
A network engineer is troubleshooting OSPF multiarea.
Which Cisco IOS XR feature should the engineer use in order to streamline OSPF issue?
- A . hierarchical CLI
- B . routing process enabled by default on all interfaces
- C . DR support for topology management
- D . show lp ospf topology command
Refer to the exhibit.

P1 and PE3 Cisco IOS XR routers are directly connected and have this configuration applied. The BGP session is not coming up. Assume that there is no IP reachability problem and both routers can open tcp port 179 to each other.
Which action fixes the issue?
- A . Change HMAC-MD5 to HMAC-SHA1-20
- B . Configure the send and accept lifetime under key 1
- C . Change HMAC-MD5 to MD5
- D . Change HMAC-MD5 to HMAC-SHA1-12
Refer to the exhibit.

A network engineer commissioned Router 1, which connects lo Router 2 and Router 5 Router 1 participates in IS-IS routing with other routers, but it is not used for transit traffic. Traffic from Router 2 to Router 5 is expected to travel via Router 1 but the traffic is travelog via Router 3 and Router 4.
Which action reserves this problem?
- A . Add hello padding on Router 1
- B . Remove the hello padding on Router 5
- C . Add the overload bit on Router 5
- D . Remove the overload bit on Router 1.