Cisco 300-510 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-510
- Exam Name: Implementing Cisco Service Provider Advanced Routing Solutions (SPRI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
What is the difference between a source tree and a shared tree in a multicast environment?
- A . To route traffic from source to receiver a source tree uses a link-state routing protocol and a shared tree uses a distance-vector routing protocol.
- B . A source tree has its root at the source, and a shared tree has its root at a designated rendezvous point.
- C . To stream multicast from source to receiver, a source tree uses PIM-SM and a shared tree uses PIM-DM.
- D . Source trees are the default type for bidirectional PIM. and PIM-DM uses shared trees by default.
B
Explanation:
Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipmulti_pim/configuration/xe-16-5/imc-pim-xe-16-5-book/imc-tech-oview.html
R2 receives a single summary route 172.16.100.0/22 for networks 172.16.100.0/24, 172.16.101.0/24, and 172.16.103.0/24.

Refer to the exhibit.

R3 is: failing to accept multicast RP information from Domain-A advertising MSDP SA messages to R1 and R4 receiving SA messages only from R4
Which command must the engineer implement to resolve the issue?
- A . R3# ip msdp sa-filter in 192.168.3.1
- B . R3# no ip msap sa-filter in 192.168.1.1
- C . R3# no ip msdp peer 192.168.1.1
- D . R3# ip msdp sa-filter out 192.168.1.1
B
Explanation:
Reference: https://allthingsnetworking.wordpress.com/2014/06/27/pim-msdp-sa-filter/
What is the difference between basic IS-IS and OSPF packet types?
- A . IS-IS and OSPF use area packets, but only IS-IS uses sequence number packets.
- B . IS-IS and OSPF use link-state update packets, but only OSPF uses link-state ACK packets.
- C . IS-IS and OSPF use Hello packets, but only OSPF uses DBD packets.
- D . IS-IS and OSPF use link-state update packets, but only IS-IS uses DBD packets.
C
Explanation:
Reference: https://www.ciscopress.com/articles/article.asp?p=26850&seqNum=4
Refer to the exhibit.

A network engineer must optimize link failures on the OSPF routing domain. The solution must follow RFC 5286. and downtime must be no more than 50 ms. All known subnets on R1 must be protected.
Which solution must the engineer implement on R1?
- A . Configure fp ospf frr per-prefix candidate enable high under the interface configuration.
- B . Configure Ip ospf fast-reroute per-prefix candidate enable under the interface configuration.
- C . Configure fast-reroute per-prefix enable prefix-priority low under the global OSPF configuration.
- D . Configure frr per-prefix enable priority high under the global OSPF configuration.
You have configured MSDP peering between two autonomous systems that pass traffic between two sites, but the peering has failed to come up.
Which task do you perform to begin troubleshooting the problem?
- A . Verify that multicast has been disabled globally
- B . Verify that PIM-DM is configured on the source interface
- C . Verify that both source interfaces are reachable from both peers
- D . Verify that the two MSDP peers allow asymmetric routing
Refer to the exhibit.





R2



Solution: –
R1
Int loopback0
Ip ospf 10 area 0
Int loopback10
Ip ospf network point-to-point
Int loopback20
Ip ospf network point-to-point
Int loopback30
Ip ospf network point-to-point
Router ospf 10
Area 1 range 172.16.100.0 255.255.252.0
Copy run start
Verification: –

Refer to the exhibit.

After configuring IS-IS on routers R1 and R2, an engineer notices that only the loopback interface at 2000:1::1 /96 is known to router R2.
Which change must be made so that only Loopback2 is advertised from R1 to R2?
- A . Configure the router isis areal command under the LoopbackO interface on R1.
- B . Remove the advertise passive-only command under the IS-IS address family ipv6 configuration
- C . Remove the ipv6 router isis areal command under the Loopback2 interface on R1.
- D . Remove the passive-interface Loopback0 command under the router isis areal configuration.
Refer to the exhibit.

An administrator is troubleshooting network issues on a customer’s network PE1 cannot form an LDP relationship with PE2 using LDP ID 192 168.1.1. Due to this connectivity issue, the customer’s routes behind both PE routers cannot be exchanged.
Which action must the administrator take to correct the problem?
- A . Configure PE2 to automatically select its own LDP router ID with 192.168.1.1.
- B . Create a targeted LDP session on PE2 to override the missing routing table entry on PEL
- C . Configure PE1 with a static route to 192 168.1.1.
- D . Enable LDP session protection on the link that P1 uses as the next hop to PE2.
An engineer is troubleshooting a connectivity issue across the MPLS network and is verifying the forwarding behavior of packets.
Which table does the engineer look at to verify the forwarding behavior of an IP packet as it enters the MPLS network at the ingress LSR?
- A . LFIB
- B . LIB
- C . RIB
- D . FIB
A
Explanation:
https://community.cisco.com/t5/image/serverpage/image-id/44142iC3B9032F415B1395?v=v2