Cisco 300-510 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-510
- Exam Name: Implementing Cisco Service Provider Advanced Routing Solutions (SPRI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
Which two differences should be considered when deciding whether to implement to implement routing policies or route maps? (Choose two.)
- A . Sequences are added after implementing a route map, but routing policies must be reconfigured when change is needed.
- B . Route maps are implemented using hierarchical policies, but routing policies must be implemented sequentially.
- C . Route maps require an explicit deny at the end of the sequence, but routing policies have an implicit deny at the end of the program.
- D . Route policies require sequence numbers, but route maps are implemented without sequencing.
- E . Route maps are supported in Cisco 10S Software and routing policies are supported in Cisco IOS XR Software.
Refer to the exhibit.

An engineer has configured all routers in the environment to run IS-IS Level 1 and Level 2 routing.
The engineer wants traffic from R1 to R5 to pass via R2. but IS-IS routing has calculated the best path via R4.
Which action corrects the problem?
- A . Configure routers R1, R4, and R5 for Level 2 routing only.
- B . Set the link metric for the link from router R1 to router R4 to 30 or more.
- C . Set the link metric on R2 for the links from router R2 to routers R3 and R4 to 30 or more.
- D . Configure routers R1, R2, and R5 for Level 1 routing only.
Refer to the exhibit.

An engineer is addressing an IS-IS design issue which is running within the topology. All
links are running on FastEthernet, except the link between R5 and R4, which is Gigabit Ethernet.
Which statement about the design is true?
- A . R4 prefer to reach R5 using R1 as the next hop
- B . All links have equal cost if the default metric is used
- C . R5 prefers to use R4 as the next hop for all routes
- D . R1 prefer to use R5 as the next hop to reach R4
Refer to the exhibit.

An engineer is troubleshooting an OSPF issue. Router 1 has a neighbor relationship with router 2. Only router 1 classful EIGRP routes can be seen on router 2.
In order for all EIGRP routes to be redistributed correctly, which action should be taken?
- A . Router 1 must have the keyword subnets included in the redistribution command for all EIGRP routes to be redistributed.
- B . Router 1 must remove the AS number 1 from the redistribution command for all EIGRP routes to be redistributed.
- C . Router 1 must have the keyword ospf-metric included in the redistribution command for all EIGRP routes to be redistributed.
- D . Router 1 must have the keyword metric-type 1 included in the redistribution command for all EIGRP routes to be redistributed.
Refer to the exhibit.

Reuters R2. R3, R4 and R5 all reside in the same area, with R1 in a different area R3 is overutilized and the engineer wants to reduce its CPU load The engineer configured router R4 to summarize routes that it receives from R5. but R3 is still receiving all of the R5 routes.
Which action resolves the issue?
- A . Configure R3 in a new area
- B . Configure R2 as a Level 1 router
- C . Configure the summary routes on R5
- D . Configure R4 as a Level I-Level 2 router
What are two features of dual-stack? (Choose two.)
- A . It is implemented without excessive processing power.
- B . It supports IPv4 and IPv6 traffic on the same infrastructure.
- C . It allows an engineer to stack multiple Layer 2 switches to serve as a single switching unit.
- D . It requires tunneling IPv6 traffic over an IPv4 infrastructure.
- E . It securely routes and tunnels traffic between separate sites over the Internet.
Refer to the exhibit.

Which effect of this configuration is true?
- A . It sets the keepalive timer to 30 seconds and the hold timer to 240 seconds.
- B . It sets the keepalive timer to 30 milliseconds and the hold timer to 240 milliseconds
- C . It sets the hold timer to 30 milliseconds and the keepalive timer to 240 milliseconds
- D . It sets the hold timer to 30 seconds and the keepalive timer to 240 seconds
A
Explanation:
Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_bgp/command/irg-cr-book/bgps1.
html#wp1552800140
Which output from the show isis interface command helps an engineer troubleshoot an IS-IS adjacency problem on a Cisco IOS-XR platform?
- A . metric
- B . priority
- C . circuit type
- D . hello interval
C
Explanation:
RP/0/0/CPU0:XR1#show isis interface | i Cir
Tue Jun 29 17:56:42.369 UTC
Circuit Type: level-1-2
Circuit Number: 0
Circuit Type: level-1
Circuit Number: 1
RP/0/0/CPU0:XR1#show isis interface | i Hel
Tue Jun 29 17:56:46.609 UTC
Refer to the exhibit.

The branch office in area 10 is connected to HQ via Frame Relay uplinks with bandwidth constraints After a recent implementation of QoS on the R2 and R3 networks the system has been logging %SYS-2-MALLOCFAIL: Memory allocation of 65536 bytes failed from 0x224E321, alignment 0 messages To reduce traffic load and memory utilization on R2 and R3 the network engineer configured R1 to announce only one user subnet per location by issuing the summary address 192.168.0.0 255.255.248.0 command en R1 However, the engineer noticed that router R2 still has two routes and a summary address from HQ and R3 also has two routes from HQ.
Which two actions must the engineer take on R1 to fix the issue so that only one route is announced? (Choose two)
- A . Configure the subnet range with the network command under the IS-IS process.
- B . Configure RI as a Level 1 device.
- C . Redistribute both routes into the ISIS process.
- D . Configure a summary route for Level 1-Level 2 devices.
- E . Configure a summary route for Level 1 devices.
Which keyword is used with the match route-type command to redistribute the external BGP and IGP routes using route map?
- A . match route-type type-1
- B . match route-type nssa-external
- C . match route-type type-2
- D . match route-type external
D
Explanation:
Reference: https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/49111-route-map-bestp.html