Cisco 300-510 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-510
- Exam Name: Implementing Cisco Service Provider Advanced Routing Solutions (SPRI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
Refer to the exhibit.

A network engineer applied configuration on R1 to summarize all ISIS routes, but R2 Is still receiving specific routes from R1. The engineer has confirmed that both routers are configured with the correct summarization configuration, but R1 is not sending the correct summary routes.
Which configuration must be applied to router R1 to summarize routes within Level 1?
- A . R1 (config-router)#summary-address 1.0.0.0 255.0.0.0 level-1-2
- B . R1(config-router)#no summary-address 1.0.0.0 255.0.0.0 level-1
- C . R1(config-router)#summary-address 1.0.0.0 255.0.0.0 level-1
- D . R1(config-router)#summary-address 1.0.0.0 255.0.0.0 level-2
Refer to the exhibit.

An engineer is troubleshooting an issue with traffic steering using the color-only automated steering mechanism. BGP is failing to automatically steer traffic into an SR policy with the given color of a route, regardless of the next hop. The layer 2 configuration is correct, and the physical connection between the devices is working normally.
Which additional command sequence must the engineer add to correct the issue?

- A . Option A
- B . Option B
- C . Option C
- D . Option D
Refer to the exhibit.

An engineer working for a private telecommunication company with an employee id 4115 46 881 is enabling a segment routing solution with these requirements.
✑ A service provider is using the default range for prefix SID.
✑ PE1 must allocate the first SID from the default range for the loopback address
✑ PE1 and PE2 loopback SID allocation should have a minimum difference of 500.
Which configuration must be implemented to meet the requirements?

- A . Option A
- B . Option B
- C . Option C
- D . Option D
Refer to the exhibit.

Router 1. Router 2. and Router 3 are co-located in an onsite data center of an office, but Router 4. Router 5. and Router 6 are installed in another data center ‘eral miles away. A network engineer is troubleshooting an RSVP-TE issue on the network. On most of the devices, the engineer can move all LSPs away from a selected dace and take it down for maintenance without interrupting traffic. However, when an interface on Router 3 is taken down, traffic on the network is disrupted.
What must the engineer enable to resolve the issue on Router 3?
- A . FRR
- B . NSR
- C . soft-preemption feature
- D . Soft-disperse
Refer to the exhibit.

An engineer is troubleshooting a network routing issue on this IS-IS network situated at the customer’s regional hub. Router 2 that runs Cisco IOS XR Software cannot see the network 10.1.1.0/24 on router 1. The Layer 2 encapsulations are correct. The ARP connectivity for the Ethernet interface that runs IS-IS is working.
Which action resolves the issue?
- A . On router 1, remove the CISCOLIVE keyword after the Ip router Isis command under interface GigabitEthernet0/2.
- B . Under the router isis command on router 1. change is-type level-1 to is-type level-2
- C . On router 1. add the CISCOLIVE keyword after the Ip router isis command under interface GigabitEthernet0/3.
- D . Under the router isis command on router 2. change is-type level-1 to is-type level-2
Refer to the exhibit.

A network operator is getting the route for 10.11.11 0/24 from two upstream providers on #XR3. The network operator must configure #XR3 to force the 10.11.11.0/24 prefix to route via next hop of 10.0.0.9 as primary when available.
Which of these can the operator use the routing policy language for, to enforce this traffic forwarding path?
- A . weight of 0 on the prefix coming from 192.168.0.2
- B . lower local preference on the prefix coming from 192.168.0.2
- C . higher local preference on the prefix coming from 192.168.0.1
- D . weight of 100 on the prefix coming from 192.168.0.1
A
Explanation:
Because Weight is the first attribute in path selection algorithm and is 0 for eBGP routes by default. If we set it to 0, router will continue from weight to the bottom, and when comparing neighbor router
IDs it will find 192.168.0.1 less than 192.168.0.2 and st path will be selected as the best
What Is a characteristic of a segment routing mapping server?
- A . It must be placed in the core of the network.
- B . It serves multiple VRFs.
- C . It must have an IGP adjacency.
- D . It applies SID mappings from one IGP instance to another IGP instance.
Refer to the exhibit.

Refer to the exhibit After recent configuration changes to a customer’s network, a network engineer notices that R2 cannot communicate with R3 Both FastEthemet interfaces on R2 and R3 are up and configured with the correct IP addresses MD5 password configured en R2 and R3 match with no issues What is the minimum change the engineer must make to enable R2 and R3 to communicate and fix the problem?
- A . Configure a loopback interface on R2 and assign it to area 0.
- B . Define area 2 as a NSSA on R2 and R3
- C . Configure virtual links between RI and R3.
- D . Configure interface F0/0 on RI and R2 to be in area O.
Refer to the exhibit.

Refer to the exhibit. An engineer is troubleshooting an issue with this network and notices that prefixes from R3 are missing on the R1 routing table Due to repeated ASN when the 10 0 0 0’8 prefix from R3 arrives at R1, BGP automatically rejects it There is no prefix-list on R1 which blocks the traffic from R3.
What should the engineer do to fix the problem so that BGP allows that prefix on R1?
- A . Configure R2 as a route reflector client of R1.
- B . Configure the allowas-in command on R1.
- C . Configure the next-hop-self command on R2.
- D . Configure identical confederation ASNs on R1 and R2.
Refer to the exhibit.

An engineer is comparing these RPL and route map configurations.
Which two conclusions will the engineer reach? (Choose two.)
- A . RPL is applying policy only on BGP IPv6 address families, but the route map is applying policy on BGP IPv4 and IPv6 address families.
- B . RPL and the route map are applying only local preference 50 for prefix 172.22.0.0/16.
- C . RPL is applying local preference 100 and community (2:100) for multiple prefixes, but the route map is applying default local preference for multiple prefixes
- D . RPL is applying local preference 50 and community (2:666) for prefix 172.22.0.0716. but the route
map is applying only local preference 50 for the same prefix - E . RPL is applying local preference 50 and community (2:666) for all prefixes, but the route map is applying only local preference 50 for all prefixes.