Cisco 300-425 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-425
- Exam Name: Designing Cisco Enterprise Wireless Networks (ENWLSD)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
In which scenario is FlexConnect mode particularly beneficial?
- A . Campuses with high-density client deployment
- B . Remote sites with local breakout of traffic
- C . Large offices using central switching
- D . Data centers with centralized resources
An engineer must optimize client roaming after noticing that clients in the environment are not roaming as expected. Upon reviewing an over- the-air packet capture, the engineer sees that the AP is sending a BSS Transition Management query to the client, which causes it to roam.
The disassociation imminent feature is not enabled on the WLAN.
What is the cause of the issue?
- A . Low RSSI check is enabled.
- B . Fast Transition is disabled.
- C . Band Select is enabled.
- D . Optimized roaming is enabled.
A network engineer is retorting an existing building wired with Category 5e with Cisco Aironet 3800 Series APs and mGig switches.
Which cable length allows for 5G operation?
- A . 70 m
- B . 120 m
- C . 130 m
- D . 150 m
When conducting a site survey for real-time traffic over wireless, which two design capabilities of smartphones and tablets must be considered? (Choose two.)
- A . no support for 802.11ac
- B . higher data rates than laptops
- C . fewer antennas than laptops
- D . no support for 802.11r
- E . lower data rates than laptops
B,E
Explanation:
![]()
Where must the APs be mounted when used in a high-density wireless network to provide 6 dB to 20 dB of attenuation to a cell?
- A . in the aisle
- B . under the seat
- C . above the stage
- D . under the stage
B
Explanation:
![]()
An engineer is designing a point-to-multipoint mesh network.
Which two AP configurations must be completed for a site survey? (Choose two.)
- A . MAP hostnames
- B . Rx power
- C . mesh on 2.4 GHz band
- D . bridge group name
- E . Tx power
An engineer is implementing a wireless design for a service provider. The design includes a Catalyst 9800, a stack of two Catalyst 9300X-48HX switches, and 9166 APs. Each AP must be named using the Floor-439412509-01X sting where X is the area number. The engineer wants to connect the APs to the switch stack using POE.
How many APs must the engineer connect to the stack so the APs run using full functionalities?
- A . all ports on switch 2 of the stack
- B . all ports on switch 1 of the stack
- C . all ports of the switches
- D . half ports per switch
A customer Wi-Fi deployment is experiencing the sticky client problem and must enable the optimized roaming feature. The wireless clients have valid security credentials for an SSID and can see an AP that offers that SSID to join.
What must be configured to enhance roaming?
- A . RSSI threshold
- B . disable DFS
- C . disable 802.11k
- D . enable data rates
How does AP failover priority for access points function when configured with priority 1 or 4?
- A . When configured with priority 1, the access point is assigned with the highest priority level and it is marked as critical. This access point fails over before other access points with the lower priority when there is primary controller failure.
- B . When configured with priority 4, the access point is assigned with the highest priority level and it is marked as critical. This access point fails over before other access points with the lower priority when there is primary controller failure.
- C . When configured with priority 4, the access point is assigned with the lowest priority level and it is marked as low. This access point fails over after other access points with the higher priority when there is primary controller failure.
- D . When configured with priority 1, the access point is assigned with the medium priority level and it is marked as medium. This access point fails over after other access points with the higher priority when there is primary controller failure.
A wireless engineer is using Ekahau site survey to validate that an existing wireless network is operating as expected, which type of survey should be using to identify the end-to-end network performance?
- A . GPS assisted
- B . Spectrum analysis
- C . Passive
- D . Active ping
B
Explanation:
https://support.ekahau.com/hc/en-us/articles/115004973067-Spectrum-Analysis-Surveys