Cisco 300-425 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-425
- Exam Name: Designing Cisco Enterprise Wireless Networks (ENWLSD)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
An engineer is designing a new wireless network.
The network needs to full the following requirements:
✑ support multimedia applications
✑ support a high concentration of wireless clients
✑ support data over wireless
✑ support roaming
Which approach should be used?
- A . use of micro cells with reduced power levels
- B . use of macro cells with reduced power levels
- C . coverage for cells at maximum power levels
- D . use of macro cells with maximum power levels
A new wireless network design has these requirements:
• AireOS WLCs as guest anchors
• a Cisco Catalyst 9800 Series WLC as the foreign controller
• use of Wi-Fi 6 APs
• inter-controller roaming for guest users
Which two design approaches meet these requirements? (Choose two.)
- A . Use EoIP for communication between controllers.
- B . Use WLC software versions that support IRCM.
- C . Use AVC on the anchor WLCs.
- D . Use IPv6 across the wireless network.
- E . Use secure mobility to pair controllers.
Refer to the exhibit. An engineer must design a mobility group that has these requirements:
• The mobility group must consist of two WLCs.
• All WLCs must run software version 8.0 or later.
• The WLCs must connect via an IPv4 network.
• Two of the WLCs must be in an SSO high availability pair.
Which two configurations must be included in the design? (Choose two.)
- A . All the WLCs must be of the same model or type.
- B . Only WLCs in an SSO high availability pair must use the same virtual IP address.
- C . The WLAN SSID must be consistent across all the WLCs.
- D . All the WLCs must run the same software version.
- E . Each WLC must use the same mobility domain name.
An engineer working for an enterprise deployed multiple Cisco WLCs. A controller that sits in the R&D division is connected through a firewall and is part of the same mobility group. The engineer must ensure that the mobility tunneling is available through the firewall and test it as R&D engineers roam the production ..within their department.
How is this requirement met?
- A . mapping on UDP port 16666 and mapping on Protocol 96 between management ports
- B . mapping on UDP port 16666 and mapping on Protocol 97 between management ports
- C . mapping on UDP port 16667 and mapping on Protocol 97 between management ports
- D . mapping on UDP port 16667 and mapping on Protocol 96 between management ports
An engineer must design and configure a wireless network for:
• pervasive coverage in an oil terminal
• casual web and email traffic
• 5 GHz
What is the best design?
- A . Keep the power assignment as auto and disable 802.11n and 802.11ac MCS rate.
- B . Disable all data rates below 24 Mbps and keep the power assignment on the AP as auto.
- C . Keep all the data rates enabled and set the AP power assignment mode to auto.
- D . Disable all data rates below 54 Mbps and assign static power level 1 on all access points.
An engineer is performing an AP-on-a-stick survey and nds that the 5 GHz channel overlap is too high when an appropriate number of APs are used for the density requirements.
Which two actions during the survey reduce channel overlap? (Choose two.)
- A . Raise the minimum data rate to 24 Mbps.
- B . Increase AP transmit power to improve the SNR.
- C . Allow the use of UNII-2e channels.
- D . Use directional antennas to limit the coverage area of some APs.
- E . Enable power saving mode.
An enterprise is using the wireless network as the main network connection for corporate users and guests. To wireless network availability. Two Standalone controllers are installed in the head office. APs are connected to the controllers using a round-robin approach to load balance the traffic. After a power cut, the wireless clients disconnect while roaming. An engineer tried eping from the controller but faits.
Which protocol needs to be allowed between the networks that the controllers are installed?
- A . IP Protocol 67
- B . IP Protocol 77
- C . IP Protocol 87
- D . IP Protocol 97
D
Explanation:
![]()
A network engineer is designing a new wireless network.
The network needs to have these characteristics:
![]()
Which approach should be taken?
- A . Deploy APs near each other for 5 GHz coverage, and disable the 2A GHz radios for some Aps.
- B . Deploy APs near each other for 2.4 GHz coverage, and disable the 5 GHz radios for all APs.
- C . Deploy APs near each other for 5 GHz coverage, and enable the 2.4 GHz radios for all Aps.
- D . Deploy APs near each other for 2.4 GHz coverage, and disable the 5 GHz radios for some APs.
C
Explanation:
https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/86/b_Cisco_Wireless_LAN_Controller_Configuration_Best_Practices.html
An enterprise network administrator is asked to set up an experimental WLAN for a collaboration project with a local service provider. The WLAN must be anchored to a WLC in the service provider data center using legacy mobility mode. After the configurations are completed on the WLCs and the firewalls in the path, the data path mobility tunnel is failing to come up.
What should be performed by the administrator to debug the issue?
- A . Establish a Telnet connection from a local PC to the firewall on port 97.
- B . Use the mapping command on the WLC.
- C . Establish a Telnet connection from a local PC to the firewall on port 16666.
- D . Use the mapping command on the WLC.
B
Explanation:
Reference: https://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/107458-wga-faq.html
Community vote distribution
What is the primary purpose of the RF profile feature in Cisco wireless controllers?
- A . To define preset security parameters
- B . To configure specific RF settings for different areas
- C . To limit the number of clients per AP
- D . To distribute load evenly across APs