Cisco 300-425 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-425
- Exam Name: Designing Cisco Enterprise Wireless Networks (ENWLSD)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
In a Cisco WLC, which setting is crucial for minimizing latency during real-time applications?
- A . Aggregation
- B . DSCP tagging
- C . Bandwidth contracts
- D . AVC profiles
A customer has two Cisco wireless controllers named WLC-A and WLC-B. Each controller is in a different building on a campus. The WLCs have different Layer 3 interfaces and broadcast the same SSIDs from their respective APs. Users must remain connected to the same VLAN and maintain their IP addresses during roaming from the APs that are attached to WLC-A and WLC-B.
Which action accomplishes the requirement?
- A . Create a mobility group between the two WLCs to allow auto-anchoring.
- B . Create an SSO cluster to ensure that client sessions sync between WLCs.
- C . Enable 802.11r on each SSID on both WLCs to allow caching of the PMK.
- D . Enable AP groups using the same name on both WLCs for each group.
An engineer configured the optimized client roaming on Cisco WLC with an RSSI threshold of 72dBm. Clients report frequent disconnections.
What must be configured for the AP to guide the client to a better AP?
- A . Enable BSS transition at the radio level and optimized roaming on the SSID.
- B . Disable coverage hole detection on the SSID and enable BSS transition on the SSID.
- C . Disable optimized roaming and enable 802.11v support on the SSID.
- D . Enable BSS transition on the SSID and optimized roaming at the radio level.
When designing a wireless network, what is the recommended signal overlap for 2.4 GHz service?
- A . 5-10%
- B . 15-20%
- C . 20-25%
- D . 30-35%
A company is in the process of relocating to a new force space and ends out that the Internet circuit will not be ready before the move. The new building has a non-Cisco WLAN to which they can connect. The engineer has a 12-port switch and one Cisco autonomous AP and must connect multiple wired devices.
Which additional device is needed to get all clients connected over the workgroup bridge?
- A . router
- B . transparent firewall
- C . hub
- D . wireless controller
Refer to the exhibit.

An enterprise is using wireless as the main network connectivity for clients. To ensure service continuity. a pair of controllers will be installed in a datacentre. An engineer is designing SSO on the pair of controllers.
What needs to be included in the design to avoid having the secondary controller go into maintenance mode?
- A . The Keep alive timer is too low. which causes synchronization problems.
- B . The connection between the redundancy ports is missing.
- C . The redundancy port must be the same subnet as the redundancy mgmt.
- D . The Global Configuration of SSO is set to Disabled on the controller.
B
Explanation:
‘There are few scenarios where the Standby WLC may go into Maintenance Mode and not be able to communicate with the network and peer:
• Non reachability to Gateway via Redundant Management Interface
• WLC with HA SKU which had never discovered peer
• Redundant Port is down
• Software version mismatch (WLC which boots up first goes into active mode and the other WLC in Maintenance Mode)’ High Availability (SSO) Deployment Guide C Cisco
WLC SSO is set up between two WLCs in a service provider network serving public spaces. On WLC failover, it is noticed that only about half of the original client count is now showing on the secondary WLC, although it is currently showing the role as active.
Which design side case explains the issue?
- A . The secondary WLC platform does not support the required client count.
- B . The WLCs had not completed database sync before the primary failure.
- C . SSO is not configured correctly.
- D . Some client sessions were in WebAuth-Req state before failover.
An engineer must install an outdoor wireless network for an area with a direct line of sight. The outdoor APs are in an open area with of harsh weather.
Which two parameters must the engineer consider to prevent an outdoor wireless outage? (Choose two.)
- A . lightning arrestor installation
- B . antenna cable grounding
- C . cable strength
- D . cable length
- E . elimination of trees
An engineer must perform an assessment of a customer LAN for a future IEEE 802.11ac Wave 2 wireless deployment All access switches are Fast Ethernet-Capable only, and the wired infrastructure between existing APs and access switches is based on the CAT 6A standard.
Which two actions provide maximum support of Cisco 3800 Series access points? (Choose two.)
- A . Replace the existing switches with mGig switches.
- B . Replace the existing switches with gigabit switches with 10G uplinks.
- C . Ensure that cable distances between access switches and APs are not longer than 100 meters.
- D . Replace the existing wiring infrastructure with the CAT-7E wiring standard,
- E . Ensure that cable distances between access switches and APs are not longer than 55 meters.
The wireless survey report shows APs staggered throughout a facility, with several of them placed on the exterior walls. Other APs are located at building corners and major turns in the structure layout.
Assuming that all survey locations are optimized with a minimum of -67 RSSI at cell edges with 20% overlapping cells, for which purpose is this survey model used?
- A . location services, VoIP, data, and video
- B . streaming video with VoIP, data, and HD resolution
- C . location-based services, BYOD preparation, and HD video streaming
- D . voice, data clients, and video on demand