Cisco 300-410 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-410
- Exam Name: Implementing Cisco Enterprise Advanced Routing and Services (ENARSI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
What does the PE router convert the Ipv4 prefix to within an MPLS VPN?
- A . VPN-IPv4 prefix combined with the 64-bit route distinguisher
- B . 48-bit route combining the IP and PE router-id
- C . prefix that combines the ASN, PE router-id, and IP prefix
- D . eBGP path association between the PE and CE sessions
A
Explanation:
![]()
Refer to the exhibit.

An engineer must advertise routes into IPv6 MP-BGP and failed.
Which configuration resolves the issue on R1?
- A . router bgp 65000
no bgp default ipv4-unicast
address-family ipv6 multicast
network 2001:DB8::/64 - B . router bgp 65000
no bgp default ipv4-unicast
address-family ipv6 unicast
network 2001:DB8::/64 - C . router bgp 64900
no bgp default ipv4-unicast
address-family ipv6 unicast
network 2001:DB8::/64 - D . router bgp 64900
no bgp default ipv4-unicast
address-family ipv6 multicast
neighbor 2001:DB8:7000::2 translate-update ipv6 multicast
Refer to the exhibit.

Which configuration command establishes an EIGRP neighbor adjacency between the hub and spoke?
- A . connected 10.1.2.192 command on spoke router
- B . network 10.1.2.192 command on spoke router
- C . eigrp-peer 10.1.2.192 command on the hub router
- D . neighbor 10.1.2.192 command on hub router
Refer to the exhibit.

R1 is configured with uRPF, and ping to R1 is failing from a source present in the R1 routing table via the GigatxtEthernet 0/0 interface.
Which action resolves the issue?
- A . Remove the access list from the interface GigabrtEthernet 0/0
- B . Modify the uRPF mode from strict to loose
- C . Enable Cisco Express Forwarding to ensure that uRPF is functioning correctly
- D . Add a floating static route to the source on R1 to the GigabitEthernet 0/1 interface
Which protocol is used in a DMVPN network to map physical IP addresses to logical IP addresses?
- A . BGP
- B . LLDP
- C . EIGRP
- D . NHRP
Refer to the exhibit.

The company implemented uRPF to address an antispoofing attack. A network engineer received a call from the IT security department that the regional data center is under an IP attack.
Which configuration must be implemented on R1 to resolve this issue?

- A . Option A
- B . Option B
- C . Option C
- D . Option D
1.2/8 via 10.2.1.2, Tunnel1 created 00:00:12, expire 01:59:47
Type. dynamic, Flags: authoritative unique nat registered used
NBMA address: 10.12.1.2
What does the authoritative flag mean in regards to the NHRP information?
- A . It was obtained directly from the next-hop server.
- B . Data packets are process switches for this mapping entry.
- C . NHRP mapping is for networks that are local to this router.
- D . The mapping entry was created in response to an NHRP registration request.
- E . The NHRP mapping entry cannot be overwritten.
Refer to the exhibit.

The AP status from Cisco DNA Center Assurance Dashboard shows some physical connectivity issues from access switch interface G1/0/14.
Which command generates the diagnostic data to resolve the physical connectivity issues?
- A . test cable diagnostics tdr interface GigabitEthernet1/0/14
- B . Check cable-diagnostics tdr interface GigabitEthernet1/0/14
- C . show cable-diagnostics tdr interface GigabitEthernet1/0/14
- D . Verify cable-diagnostics tdr interface GigabitEthernet1/0/14
A
Explanation:
The Time Domain Reflectometer (TDR) feature allows you to determine if a cable is OPEN or SHORT when it is at fault.
To start the TDR test, perform this task:
Step 1 (Starts the TDR test): test cable-diagnostics tdr {interface {interface-number}}
Step 2 (Displays the TDR test counter information): show cable-diagnostics tdr {interface interface-number}
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9600/software/release/16-11/configuration_guide/int_hw/b_1611_int_and_hw_9600_cg/checking_port_status_and_connecti vity.pdf

Text, table Description automatically generated
Refer to the exhibit.


An engineer configures DMVPN and receives the hub location prefix of 10.1.1.0724 on R2 and R3 The R3 prefix of 10 1.3.0/24 is not received on R2. and the R2 prefix 10.1,2.0/24 is not received on R3.
Which action reserves the issue?
- A . Split horizon prevents the routes from being advertised between spoke routers it should be disabled with the command no ip split-horizon eigrp 10 on the tunnel interface of R1
- B . There is no spoke-to-spoke connection DMVPN configuration should be modified to enable a tunnel connection between R2 and R3 and neighbor relationship confirmed by use of the show ip eigrp neighbor command
- C . Split horizon prevents the routes from being advertised between spoke routers it should be disabled with the no ip split-horizon eigrp 10 command on the Gi0/0 interface of R1.
- D . There is no spoke-to-spoke connection DMVPN configuration should be modified with a manual neighbor relationship configured between R2 and R3 and confirmed bb use of the show ip eigrp neighbor command.
A
Explanation:
In this topology, the Hub router will receive advertisements from R2 Spoke router on its tunnel
interface. The problem here is that it also has a connection with R3 Spoke on that same tunnel
interface. If we don’t disable split-horizon, then the Hub will not relay routes from R2 to R3 and the
other way around. That is because it received those routes on the same interface tunnel and therefore
it cannot advertise back out that same interface (split-horizon rule). Therefore we must disable splithorizon on the Hub router to make sure the Spokes know about each other.
Refer to the exhibit.

An engineer investigates an IPv6 EIGRP neighbor adjacency issue that sees the neighbors flapping and issued a ping from R1 to its directly connected neighbor. The link between the switches is stable at Layer 2. and other connected devices are also functioning.
Which action resolves the issue?
- A . The switch between the two neighbors is not IPv6 compatible and must be replaced with an IPv6 compatible device.
- B . Data is not reliably transmitted between the dynamically assigned link-local addresses of the routers and must be manually assigned.
- C . Multicast packets are not reliably transmitted over the link, and the switch must be replaced.
- D . The switch between the two neighbors is not configured for IPv6 multicast and must be configured for IPv6 multicast.