Cisco 300-410 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-410
- Exam Name: Implementing Cisco Enterprise Advanced Routing and Services (ENARSI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
DRAG DROP
Drag and drop the operations from the left onto the locations where the operations are performed on the right.

Explanation:
Label Switch Router
Refer to the exhibit.

Refer to the exhibit. A network engineer receives a report that Spoke 1 users can perform bank transactions with the server located at the Center site, but Spoke 2 users cannot.
Which action resolves the issue?
- A . Configure the Spoke 2 users IP on the router B OSPF domain
- B . Configure encapsulation dot1q 78 on the router C interface.
- C . Configure IPv6 on the routers B and C interfaces
- D . Configure OSPFv2 on the routers B and C interfaces
Refer to the exhibit.

During ISP router maintenance, the network produced many alerts because of the flapping interface.
Which configuration on R1 resolves the issue?
- A . no snmp trap link-status
- B . snmp trap link-status down
- C . snmp trap ip verify drop-rate
- D . ip verify drop-rate notify hold-down 60
Refer to the exhibit.

APC is configured to obtain an IP address automatically, but it receives an IP address only from the 169.254.0.0 subnet The DHCP server logs contained no DHCPDISCOVER message from the MAC address of the PC.
Which action resolves the issue?
- A . Configure an ip helper-address on the router to forward DHCP messages to the server.
- B . Configure DHCP Snooping on the switch to forward DHCP messages to the server.
- C . Configure a DHCP reservation on the server for the PC.
- D . Configure a static IP address on the PC and exclude it from the DHCP pool.
DRAG DROP
Drag and drop the descriptions from the left onto the corresponding MPLS components on the right.

Explanation:
Table Description automatically
generated
Refer to the exhibit.

An engineer must establish a point-to-point GRE VPN between R1 and the remote site.
Which configuration accomplishes the task for the remote site?
- A . Interface Tunnel1
tunnel source 199.1.1.1
tunnel destination 200.1.1.3
ip address 192.168.1.3 255.255.255.0 - B . Interface Tunnel1
tunnel source 200.1.1.3
tunnel destination 199.1.1.1
ip address 192.168.1.1.255.255.255.0 - C . Interface Tunnel1
tunnel source 200.1.1.3
tunnel destination 199.1.1.1
ip address 192.168.1.3.255.255.255.0 - D . Interface Tunnel
tunnel source 199.1.1.1
tunnel destination 200.1.1.3
ip address 192.168.1.1.255.255.255.0
Refer to Exhibit.
A network administrator has successfully configured DMVPN topology between a hub and two spoke routers.
Which two configuration commands should establish direct communications between spoke 1 and spoke 2 without going through the hub? (Choose two).

- A . At the hub router, configure the ip nhrp shortcut command.
- B . At the spoke routers, configure the ip nhrp spoke-tunnel command.
- C . At the hub router, configure ip nhrp redirect the command
- D . At the spoke routers, configure the ip nhrp shortcut command.
- E . At the hub router, configure tne Ip nhrp spoke-tunnel command
C,D
Explanation:
To configure Spoke to Spoke communication we can configure DMVPN Phase II or Phase III. But in Phase II, the first few packets would go through Hub. In order tototally ignore the hub, we have to
use DMVPN Phase III:
DMVPN Phase III is same as Phase 2 but removes some restrictions and complexities of Phase 2. Also allows greater variety of DMVPN network designs we use:+ ip nhrp redirect in hub: tells the initiator spoke to look for a better path to the destination spoke than through the Hub. Upon receiving the NHRP redirect message thespokes communicate with each other over the hub and they have their NHRP replies for the NHRP Resolution Requests that they sent out.+ ip nhrp shortcut in spokes: overwrite the CEF table on the spoke. It basically overrides the next-hop value for a remote spoke network from the default initial hubtunnel IP address to the NHRP resolved remote spoke tunnel IP address)
A company Is redesigning WAN infrastructure so that all branch sites must communicate via the head office and the head office can directly communicate with each site independently. The network engineer must configure the head office router by considering zero-touch technology when adding new sites in the same WAN infrastructure.
Which configuration must be applied to the head office router to meet this requirement?

- A . Option A
- B . Option B
- C . Option C
- D . Option D
The network administrator is tasked to configure R1 to authenticate telnet connections based on Cisco ISE using RADIUS. ISE has been configured with an IP address of 192.168.1.5 and with a network device pointing towards R1 (192.168.1.1) with a shared secret password of Cisco123. If ISE is down, the administrator should be able to connect using the local database with a username and password combination of admin/cisco123.
The administrator has configured the following on R1:

ISE has gone down. The Network Administrator is not able to Telnet to R1 when ISE went down.
Which two configuration changes will fix the issue? (Choose two.)

- A . Option A
- B . Option B
- C . Option C
- D . Option D
- E . Option E
A network engineer needs to verify IP SLA operations on an interface that shows on indication of excessive traffic.
Which command should the engineer use to complete this action?
- A . show frequency
- B . show track
- C . show reachability
- D . show threshold