Cisco 300-410 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-410
- Exam Name: Implementing Cisco Enterprise Advanced Routing and Services (ENARSI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
Refer to the exhibit.

An administrator noticed that after a change was made on R1, the timestamps on the system logs did not match the clock.
What is the reason for this error?
- A . An authentication error with the NTP server results in an incorrect timestamp.
- B . The keyword localtime is not defined on the timestamp service command.
- C . The NTP server is in a different time zone.
- D . The system clock is set incorrectly to summer-time hours.
Refer to the exhibit.

A network engineer is provisioning end-to-end traffic service for two different enterprise networks with these requirements
✑ The OSPF process must differ between customers on HQ and Branch office routers, and adjacencies should come up instantly.
✑ The enterprise networks are connected with overlapping networks between HO and a branch office
Which configuration meets the requirements for a customer site?
A)

B)

C)

D)

- A . Option A
- B . Option B
- C . Option C
- D . Option D
What are the two reasons for RD and VPNv4 addresses in an MPLS Layer 3 VPN? (Choose two.)
- A . RD is prepended to each prefix to make routes unique.
- B . VPN RT communities are used to identify customer unique routes.
- C . When the PE redistributes customer routes into MP-BGP, they must be unique.
- D . They are on a CE device to use for static configuration.
- E . They are used for a BGP session with the CE device.
Refer to the exhibit.

A network engineer is troubleshooting a failed link between R2 and R3 No traffic loss is reported from router R5 to HQ.
Which command fixes the separated backbone?
- A . R2(config-router)#no area 21 stub
- B . R2(config_router)#area 21 virtual-link 192.168.125.5
- C . R3(config-router)#area 21 virtual-link 192.168.125.5
- D . R3(config-router)#no area 21 stub
Refer to the exhibit.

Reachability between servers in a network deployed with DHCPv6 is unstable.
Which command must be removed from the configuration to make DHCPv6 function?
- A . ipv6 dhcp server DHCPPOOL
- B . ipv6 address 2001:0:1:4::/64
- C . ipv6 nd ra suppress
- D . address prefix 2001:0:1:4::/64 lifetime infinite infinite
Refer to the exhibit.

The forwarding entries how that the next hop for prefixes from the 172.16.0.0/16 network is set to 10.2.2.2 instead of 10.1.1.1.
Which action resolves the issue?
- A . Add set ip next hop 10.1.1.1 in route-map RED permit 20.
- B . Add the continue statement in route-map RED permit 10 instead of continue 20.
- C . Remove match ip address prefix-list 1 from route-map RED permit 10.
- D . Remove the continue 20 statement from route-map RED permit 10
Refer to the exhibit.

R1 and R2 are configured for EIGRP peering using authentication and the neighbors failed to come up.
Which action resolves the issue?
- A . Configure a matching key-id number on both routers
- B . Configure a matching lowest key-id on both routers
- C . Configure a matching key-chain name on both routers
- D . Configure a matching authentication type on both router
Refer to the exhibit.

The branch router is configured with a default route toward the internet and has no routes configured for the HQ site that is connected through interface G2/0. The HQ router is fully configured and does not require changes.
Which configuration on the branch router makes the intranet website (TCP port 80) available to the branch office users?
- A . access-list 100 permit tcp any host intranet-webserver-ip eq 80
!
route-map pbr permit 10
match ip address 100
set ip next-hop 192.168.2.2
!
interface G2/0
ip policy route-map pbr - B . access-list 101 permit tcp any any eq 80
access-list 102 permit tcp any host intranet-webserver-ip
!
route-map pbr permit 10
match ip address 101 102
set ip next-hop 192.168.2.2
!
interface G1/0
ip policy route-map pbr - C . access-list 101 permit tcp any any eq 80
access-list 102 permit tcp any host intranet-webserver-ip
!
route-map pbr permit 10
match ip address 101
set ip next-hop 192.168.2.2
route-map pbr permit 20
match ip address 102
set ip next-hop 192.168.2 2
!
interface G2/0
ip policy route-map pbr - D . acceslist 100 permit tcp host intranet-webserverip eq 80 any
!
route-map pbr permit 10 match ip address 100
set ip next-hop 192.168 2.2
!
interface G1/0
ip policy route-map pbr
B
Explanation:
the ACL 101 matches all HTTP pakects while the ACL 102 matches TCP packets destined to Intranet webserver. These packets will be sent to HQ router.
If a match command refers to several objects in one command, either of them should match (the logical OR algorithm is applied). For example, in the match ip address 101 102 command, a route is permitted if it is permitted by access list 101 or access list 102.
Refer to the exhibit.

R1 cannot establish a neighbor relationship with R2.
Which action resolves the issue"?
- A . Configure the mtu Ignore command on the Interfaces of R1 and R2
- B . Configure the ip ospf network point-to-point command on the interfaces of R1 and R2
- C . Configure the ip ospf network broadcast command on the interfaces of R1 and R2
- D . Configure the neighbor 2.2.2.2 command on R1 under the OSPF process
A
Explanation:
In OSPF (Open Shortest Path First), the MTU (Maximum Transmission Unit) size must match on both sides of a link for OSPF neighbors to form an adjacency12. If the MTU sizes do not match, the OSPF adjacency will not form, and the routers will not become neighbors12.
In this case, R1 cannot establish a neighbor relationship with R2. One possible reason for this could be a mismatch in the MTU size on the interfaces of R1 and R212.
To resolve this issue, you can configure the mtu ignore command on the interfaces of R1 and R2 (Option A). This command allows OSPF to ignore the MTU size when determining if it can form an adjacency with a neighbor12. This means that even if the MTU sizes do not match, OSPF will still form an adjacency, and R1 and R2 will become neighbors12.
Reference: OSPF MTU Mismatch – NetworkLessons.com
Understanding OSPF MTU Mismatch Conditions and Solutions – Cisco
Refer to the exhibit.

R4 is experiencing packet drop when trying to reach 172.16.2.7 behind R2.
Which action resolves the issue?
- A . Insert a /16 floating static route on R2 toward R3 with metric 254
- B . Insert a /24 floating static route on R2 toward R3 with metric 254
- C . Enable auto summarization on all three routers R1, R2, and R3
- D . Disable auto summarization on R2