Cisco 300-410 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-410
- Exam Name: Implementing Cisco Enterprise Advanced Routing and Services (ENARSI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
Refer to the exhibit.

An engineer is investigating an OSPF issue reported by the Cisco DNA Assurance Center.
Which action resolves the issue?
- A . One of the neighbor links is down Bring the interface up by running shut and no shut
- B . One of the interfaces is using the wrong MTU Match interface MTU on both links
- C . An ACL entry blocking multicast on the interfaces Allow multicast through the interface ACL
- D . One of the interfaces is using the wrong authentication Match interface authentication on both links
The network administrator configured CoPP so that all SNMP traffic from Cisco Prime located at 192.168.1.11 toward the router CPU is limited to 1000 kbps.
Any traffic that exceeds this limit must be dropped.
access-list 100 permit udp any any eq 161
!
class-map CM-SNMP
match access-group 100
!
policy-map PM-COPP
class CM-SNMP
police 1000 conform-action transmit
!
control-plane
service-policy input PM-COPP
The network administrator is not getting the desired result for the SNMP traffic and SNMP traffic is getting dropped frequently.
Which set of configurations resolves the issue?
- A . no access-list 100
access-list 100 permit tcp host 192.168.1.11 any eq 161 - B . no access-list 100
access-list 100 permit udp host 192.168.1.11 any eq 161
!
policy-map PM-COPP
class CM-SNMP
no police 1000 conform-action transmit
police 1000000 conform-action transmit
!
control-plane
no service-policy input PM-COPP
!
interface E 0/0
service-policy input PM-COPP
!
interface E 0/1
service-policy input PM-COPP - C . no access-list 100
access-list 100 permit udp host 192.168.1.11 any eq 161
!
policy-map PM-COPP
class CM-SNMP
no police 1000 conform-action transmit
police 1000000 conform-action transmit - D . policy-map PM-COPP class CM-SNMP
no police 1000 conform-action transmit police 1000000 conform-action transmit
C
Explanation:
In the context of Control Plane Policing (CoPP) in Cisco devices, the rate limit is specified in bits per second (bps), not kilobits per second (kbps). Therefore, a limit of 1000 kbps should indeed be entered as 1,000,000 bps in the CoPP configuration.
Also, the access list should be configured to match the specific SNMP traffic from the Cisco Prime IP address (192.168.1.11), as you correctly pointed out.
Here’s the corrected configuration:
no access-list 100
access-list 100 permit udp host 192.168.1.11 any eq 161
!
policy-map PM-COPP
class CM-SNMP
no police 1000 conform-action transmit
police 1000000 conform-action transmit
This configuration ensures that only the SNMP traffic from Cisco Prime is policed and any excess traffic is dropped, preventing the router’s CPU from being overwhelmed.
Which two labet distribution methods are used by routers in MPLS? (Choose two)
- A . targeted hello message
- B . LDP discovery hello message
- C . LDP session protection message
- D . downstream unsolicited
- E . downstream on demand
Which two labet distribution methods are used by routers in MPLS? (Choose two)
- A . targeted hello message
- B . LDP discovery hello message
- C . LDP session protection message
- D . downstream unsolicited
- E . downstream on demand
Refer to the exhibits.


A user on the 192.168.1.0/24 network can successfully ping 192.168.3.1, but the administrator cannot ping 192.168.3.1 from the LA router.
Which set of configurations fixes the issue?
A)

B)

C)

D)

- A . Option A
- B . Option B
- C . Option C
- D . Option D
Refer to the exhibit.

The engineer configured and connected Router2 to Router1. The link came up but could not establish a Telnet connection to Router1 IPv6 address of 2001:DB8::1.
Which configuration allows Router2 to establish a Telnet connection to Router1?
- A . jpv6 unicast-routing
- B . permit ICMPv6 on access list INGRESS for Router2 to obtain IPv6 address
- C . permit ip any any on access list EGRESS2 on Router1
- D . IPv6 address on GigabitEthernet0/0
D
Explanation:
————————– R1———————————————
interface Ethernet0/0
ip address 209.165.201.1 255.255.255.0
ip access-group EGRESS2 out
ipv6 address 2001:DB8::1/64
end
———————-R2————————————————–
interface Ethernet0/0
ip address 209.165.201.25 255.255.255.0
ipv6 address 2001:DB8::2/64
ipv6 address autoconfig
ipv6 nd autoconfig default-route
ipv6 nd cache expire 60
ipv6 nd ra suppress
ipv6 traffic-filter INGRESS in
end
IOU_Router2#telnet 2001:DB8::1
Trying 2001:DB8::1 … Open
IOU_Router1>
——————————————————————————
Refer to the exhibit.

An administrator configured a Cisco router for TACACS authentication, but the router is using the local enable password instead.
Which action resolves the issue?
- A . Configure the aaa authentication login admin group admin local enable command instead.
- B . Configure the aaa authentication login admin group tacacs* local enable none command instead.
- C . Configure the aaa authentication login admin group tacacs* local if-authenticated command instead.
- D . Configure the aaa authentication login default group admin local if-authenticated command instead.
Refer to the exhibit.

The route to 192 168 200 0 is flapping between R1 and R2.
Which set of configuration changes resolves the flapping route?

- A . Option A
- B . Option B
- C . Option C
- D . Option D
Refer to the exhibit.

An administrator that is connected to the console does not see debug messages when remote users log in.
Which action ensures that debug messages are displayed for remote logins?
- A . Enter the transport input ssh configuration command.
- B . Enter the terminal monitor exec command.
- C . Enter the logging console debugging configuration command.
- D . Enter the aaa new-model configuration command.
C
Explanation:
The Dlogging console‖ is a default and hidden command.
Refer to the exhibit.

In which circumstance does the BGP neighbor remain in the idle condition?
- A . if prefixes are not received from the BGP peer
- B . if prefixes reach the maximum limit
- C . if a prefix list is applied on the inbound direction
- D . if prefixes exceed the maximum limit
D
Explanation:
https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/25160-bgp-maximum-prefix.html#b