Cisco 300-410 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-410
- Exam Name: Implementing Cisco Enterprise Advanced Routing and Services (ENARSI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
Exhibit:

Bangkok is using ECMP to reach to the 192.168.5.0/24 network. The administrator must configure Bangkok in such a way that Telnet traffic from 192.168.3.0/24 and192.168.4.0/24 networks uses the HongKong router as the preferred router.
Which set of configurations accomplishes this task?
- A . access-list 101 permit tcp 192.168.3.0 0.0.0.255 192.168.5.0 0.0.0.255
access-list 101 permit tcp 192.168.4.0 0.0.0.255 192.168.5.0 0.0.0.255
!
route-map PBR1 permit 10
match ip address 101
set ip next-hop 172.18.1.2
interface Ethernet0/3
ip policy route-map PBR1 - B . access-list 101 permit tcp 192.168.3.0 0.0.0.255 192.168.5.0 0.0.0.255 eq 23
access-list 101 permit tcp 192.168.4.0 0.0.0.255 192.168.5.0 0.0.0.255 eq 23
!
route-map PBR1 permit 10
match ip address 101
set ip next-hop 172.18.1.2
interface Ethernet0/1
ip policy route-map PBR1 - C . access-list 101 permit tcp 192.168.3.0 0.0.0.255 192.168.5.0 0.0.0.255 eq 23
access-list 101 permit tcp 192.168.4.0 0.0.0.255 192.168.5.0 0.0.0.255 eq 23
!
route-map PBR1 permit 10
match ip address 101
set ip next-hop 172.18.1.2
!
interface Ethernet0/3
ip policy route-map PBR1 - D . access-list 101 permit tcp 192.168.3.0 0.0.0.255 192.168.5.0 0.0.0.255
access-list 101 permit tcp 192.168.4.0 0.0.0.255 192.168.5.0 0.0.0.255
!
route-map PBR1 permit 10
match ip address 101
set ip next-hop 172.18.1.2
!
interface Ethernet0/1
ip policy route-map PBR1
C
Explanation:
We need to use Policy Based Routing (PBR) here on Bangkok router to match the traffic from 192.168.3.0/24 & 192.168.4.0/24 and “set ip next-hop” to HongKong router(172.18.1.2 in this case).
Note: Please notice that we have to apply the PBR on incoming interface e0/3 to receive traffic from 192.168.3.0/24 and 192.168.4.0/24.
Refer to the exhibit.

What is the result of applying this configuration?
- A . The router can form BGP neighborships with any other device.
- B . The router cannot form BGP neighborships with any other device.
- C . The router cannot form BGP neighborships with any device that is matched by the access list named “BGP”.
- D . The router can form BGP neighborships with any device that is matched by the access list named “BGP”.
C
Explanation:
after bgp session are UP.I configured the CoPP to drop 10.3.3.3 bgp traffic (R3).
R3 bgp traffic that matched the ACL 100 is dropped and the state is in IDLE
——————————————–
access-list 100 permit tcp host 10.3.3.3 any eq bgp
access-list 100 permit tcp host 10.3.3.3 eq bgp any
!
class-map match-all class-bgp
match access-group 100
!
policy-map policy-bgp
class class-bgp
drop
!
control-plane
service-policy input policy-bgp
!
The 10.3.3.3 neighbor goes to IDLE
Refer to the exhibit.

An engineer configures the router 10.1.100.10 for EIGRP auto summarization so that R1 should receive the summary route of 10.0.0.0/8. However, R1 receives more specific /24 routes.
Which action resolves this issue?
- A . Router R1 should configure ip summary address eigrp (AS number) 10.0.0.0 255.0.0.0 for the R1 Fast Ethernet 0/0 connected interface.
- B . Router R1 should configure ip route 10.0.0.0 255.0.0.0 null 0 for the routes that are received on R1.
- C . Router 10.1.100.10 should configure ip route 10.0.0.0 255.0.0.0 null 0 for the routes that are summarized toward R1.
- D . Router 10.1.100.10 should configure ip summary address eigrp (AS number) 10.0.0.0 255.0.0.0 for the R1 Fast Ethernet 0/0 connected interface.
Refer to the exhibits.


London must reach Rome using a faster path via EIGRP if all the links are up but it failed to take this path.
Which action resolves the issue?
- A . Increase the bandwidth of the link between London and Barcelona
- B . Use the network statement on London to inject the 172 16 X 0/24 networks into EIGRP.
- C . Change the administrative distance of RIP to 150
- D . Use the network statement on Rome to inject the 172 16 X 0/24 networks into EIGRP
Which technique removes the outermost label of an MPLS-tagged packet before the packet is forwarded to an adjacent LER?
- A . label swap
- B . explicit-null
- C . label imposition
- D . PHP
Refer to the exhibit.

A network engineer lost remote access to the router due to a network problem. The engineer used the console to access the router and noticed continuous logs on the console terminal.
Which configuration limits the number of log messages on the console to critical and higher seventy level messages?
- A . term no monitor
- B . logging console 2
- C . no logging console
- D . logging console 5
Refer to the exhibit.

Which routes from OSPF process 5 are redistributed into EIGRP?
- A . E1 and E2 subnets matching access list TO-OSPF
- B . E1 and E2 subnets matching prefix list TO-OSPF
- C . only E2 subnets matching access list TO-OSPF
- D . only E1 subnets matching prefix listTO-OS1
Refer to the exhibit.

The DHCP client is unable to receive an IP address from the DHCP server RouterB is configured as follows:

Which command is required on the fastethernet 0/0 interface of RouterB to resolve this issue?
- A . RouterB(config-if)#lp helper-address 172.31.1.1
- B . RouterBiconfig-ififclp helper-address 255.255 255 255
- C . RouterB(config-if)#lp helper-address 172.16.1.1
- D . RouterB(config-if)#lp helper-address 172.16.1.2
Refer to the exhibit.

An engineer must configure a per VRF for TACACS+ for company A.
Which configuration on RTG-1 accomplishes the task?

- A . Option A
- B . Option B
- C . Option C
- D . Option D
Refer to the exhibit.

An engineer noticed that the router log messages do not have any information about when the event occurred.
Which action should the engineer take when enabling service time stamps to improve the logging functionality at a granular level?
- A . Replace OSPF process 10 on the interfaces with OSPF process 1 and configure an additional router IO with IPv6 address
- B . Replace OSPF process 10 on the interfaces with OSPF process 1. and remove process 10 from the global configuration
- C . Replace OSPF process 10 on the interfaces with OSPF process 1 for the IPv6 address and remove process 10 from the global configuration
- D . Replace OSPF process 10 on the interfaces with OSPF process 1 for the IPv4 address and remove process 10 from the global configuration