Cisco 300-410 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-410
- Exam Name: Implementing Cisco Enterprise Advanced Routing and Services (ENARSI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
Refer to the exhibit.

A network administrator configured NTP on a Cisco router to get synchronized time for system and logs from a unified time source The configuration did not work as desired.
Which service must be enabled to resolve the issue?
- A . Enter the service timestamps log datetime localtime global command.
- B . Enter the service timestamps log datetime synchronize global command.
- C . Enter the service timestamps log datetime console global command.
- D . Enter the service timestamps log datetime clock-period global command
A
Explanation:
If a router is configured to get the time from a Network Time Protocol (NTP) server, the times in the router’s log entries may be different from the time on the systemclock if the [localtime] option is not in the service timestamps log command. To solve this issue, add the [localtime] option to the service timestamps log command. Thetimes should now be synchronized between the system clock and the log message timestamps.
Reference: https://community.cisco.com/t5/networking-documents/router-log-timestamp-entries-are-different-from-the-system-clock/ta-p/3132258
Refer to the exhibit.

An engineer implemented an access list on R1 to allow anyone to Telnet except R2 Loopback0 to R1 Loopback4 How must sequence 20 be replaced on the R1 access list to resolve the issue?
- A . sequence 20 permit tcp host 1001 ABC:2011:7:: 1 host 400A:0:400C::1 eq telnet
- B . sequence 20 deny tcp host 400A:0:400C::1 host 1001 :ABC:2011:7::1 eq telnet
- C . sequence 20 deny tcp host 1001:ABC:2011:7::1 host 400A:0:400C::1 eq telnet
- D . sequence 20 permit tcp host 400A:0:400C::1 host 1001ABC:2011:7::1 eq telnet
Refer to the exhibit.

Branch 2 hosts cannot receive dynamic IP addresses.
Which action resolves the issue?
- A . Configure the ip helper command on the interface GigabitEthernet 0/2 of the R2 router
- B . Configure the Ip helper command on the Layer 2 switch SW2 interfaces
- C . Configure the Ip helper command on the interface GigabitEthernet 0/2 of the DHCP router.
- D . Configure the Ip helper command on the interface GigabitEthernet 0/0 of the DHCP router.
An engineer configured the wrong default gateway for the Cisco DNA Center enterprise interface during the install.
Which command must the engineer run to correct the configuration?
- A . sudo maglev-config update
- B . sudo maglev install config update
- C . sudo maglev reinstall
- D . sudo update config install
Which router attaches the VPN label to incoming packets from CE routing?
- A . CE router
- B . core router
- C . P router
- D . PE router
Refer to the exhibit.

An engineer configured BGP and wants to select the path from 10.77.255.57 as the best path instead of current best path.
Which action resolves the issue?
- A . Configure AS_PATH prepend for the desired best path
- B . Configure higher MED to select as the best path.
- C . Configure lower LOCAL_PREF to select as the best path.
- D . Configure AS_PATH prepend for the current best path
Refer to the exhibit.

Why is user authentication being rejected?
- A . The TACACS+ server expects “user”, but the NT client sends “domain/user”.
- B . The TACACS+ server refuses the user because the user is set up for CHAP.
- C . The TACACS+ server is down, and the user is in the local database.
- D . The TACACS+ server is down, and the user is not in the local database.
D
Explanation:
Reference: https://www.cisco.com/c/en/us/support/docs/security-vpn/terminal-access-controller-accesscontrol-system-tacacs-/13864-tacacs-pppdebug.html
Refer to the exhibit.

Which interface configuration must be configured on the HUB router to enable MVPN with mGRE mode?

- A . Option A
- B . Option B
- C . Option C
- D . Option D
C
Explanation:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_conn_dmvpn/configuration/15-mt/sec-conn-dmvpn-15-mt-book/sec-conn-dmvpn-dmvpn.html
Refer to the exhibit.

Which configuration configures a policy on R1 to forward any traffic that is sourced from the 192.168.130.0/24 network to R2?


- A . Option A
- B . Option B
- C . Option C
- D . Option D
Refer to the exhibit.

A network engineer received a call from the vendor for a failed attempt to remotely log in to their managed rooter loopback interface from 192 168.40 15.
Which action must the network engineer take to resolve the issue?
- A . The IP access list VENDOR must be applied to interface loopback 100
- B . The time-range configuration must be changed to use absolute instead of periodic
- C . The EIGRP configuration must be updated to include a network statement for loopback 100
- D . The source IP summarization must be updated to include the vendor source IP address