DELL EMC D-PE-OE-23 Practice Exams
Last updated on Oct 23,2026- Exam Code: D-PE-OE-23
- Exam Name: Dell Technologies PowerEdge Operate 2023
- Certification Provider: DELL EMC
- Latest update: Oct 23,2026
What is a valid password option available from the iDRAC9 Unique ID feature?
- A . Encryption Default
- B . Secure Default
- C . Legacy Generated
- D . Randomly Generated
What does OBPAR allow on a PowerEdge MX750c?
- A . Run a compute sled with memory overclocking.
- B . Boot a compute sled with only one CPU.
- C . Run a compute sled with maximum performance.
- D . Boot a compute sled with reduced frequency.
The administrator plans to deploy secure connect gateway in the environment. The environment consists of Windows, Linux, and VMware.
Where should the application be installed?
- A . Can deploy a system running OS X and install on the system
- B . Must implement as system running a Windows OS and install on the system
- C . Must be installed on a PowerEdge server running iDRAC9
- D . Can be installed on a virtual machine running the Linux OS
A technician is tasked to perform a RAID Level Migration (RLM) of a RAID 5 array to a RAID 6 array. They back up data and look in iDRAC Storage and find that the current RAID 5 array is sliced into two virtual disks.
What should the technician do to achieve the desired RAID level?
- A . Reboot and press Ctrl-R to complete RAID migration
- B . Use iDRAC GUI under Storage Configuration to delete the arrays and recreate the new RAID 6 array
- C . Open the OpenManage Enterprise GUI, delete the arrays, and recreate the new RAID 6 array
- D . Use SupportAssist Enterprise to complete RAID migration
A technician installs a NIC on a single CPU server. However, the NIC is not detected when they power on the server.
What should the technician verify to make sure that the NIC is detected correctly?
- A . NIC driver is up to date
- B . System Setup is set to BIOS boot mode
- C . NIC is installed in an expansion slot managed by the single CPU
- D . Network cable is plugged into the newly installed NIC
A technician accesses the iDRAC to set up scheduled updates. This option is not available on one server, but is available on the other servers. The servers are the same model and have the same iDRAC firmware revisions.
What is required so that the technician can enable scheduled updates on the server?
- A . Update option enabled in Lifecycle Controller interface
- B . iDRAC reset using racadm racreset command
- C . iDRAC license at the Enterprise level
- D . LC Settings in Lifecycle Controller set up correctly
A company is implementing Superna Eyeglass to automate and orchestrate SyncIQ failover and failback.
What is one of the requirements when implementing Superna Eyeglass for a Dell EMC Isilon cluster?
- A . Dedicated IP pool must exist
- B . Administrator account must be used
- C . Dedicated subnet must exist
- D . System Access zone must be used
A company is implementing Superna Eyeglass to automate and orchestrate SyncIQ failover and failback.
What is one of the requirements when implementing Superna Eyeglass for a Dell EMC Isilon cluster?
- A . Dedicated IP pool must exist
- B . Administrator account must be used
- C . Dedicated subnet must exist
- D . System Access zone must be used
A technician suspects that a firmware revision is corrupt. A newer revision is not available and the customer does not want to downgrade to a lower revision.
What should be done when troubleshooting for possible corrupt firmware?
- A . Upload the same firmware revision level
- B . Reset the iDRAC
- C . Use the Lifecycle Controller Parts Replacement feature to bring the components up to the latest firmware revision levels
- D . Disable and re-enable the component then reboot the server
A new server with default iDRAC network configurations is plugged into a segregated management network configured for 10.0.0.x/24. The technician cannot connect to the iDRAC.
How can the on-site technician configure the iDRAC for network access?
- A . Change iDRAC network settings from a workstation on the management network
- B . Perform an AC power cycle to reset the iDRAC
- C . Modify the iDRAC settings using the iDRAC Direct feature
- D . Configure a DHCP reservation for the iDRAC MAC address