DELL EMC D-PCM-DY-23 Practice Exams
Last updated on Nov 16,2026- Exam Code: D-PCM-DY-23
- Exam Name: Dell PowerSwitch Campus Deploy 2023
- Certification Provider: DELL EMC
- Latest update: Nov 16,2026
A switch interface has been properly configured for static port security with one defined allowable MAC address. However, when the network administrator plugs a switch into that port, multiple devices are still allowed access to the network.
Where must port security also be enabled to have an effect?
- A . Enabled globally on the switch
- B . Enabled on all attached devices
- C . Enabled on all switches in the network
- D . Enabled on all interfaces of the switch
A network administrator is planning a PoE budget for their network.
What is the PoE source maximum power budget for a Class 4 end device?
- A . 12.95 watts
- B . 15.4 watts
- C . 34.2 watts
- D . 60 watts
If VoIP traffic uses multiple QoS prioritization schemes, what refers to VoIP traffic?
- A . COS 2, DSCP 22, AF
- B . COS 2, DSCP 46, EF
- C . COS 5, DSCP 42, AF
- D . COS 5, DSCP 46, EF
A Dell EMC N3048P with two power supplies is configured for Class-Based Power Management.
The switch has the following devices connected and fully operational:
10x 802.3af PDs negotiating as Class0 devices
10x 802.3af PDs negotiating as Class4 devices
10x 802.3at PDs negotiating as Class4 devices
How much power is reserved from the PSE budget by the devices referenced above?
- A . 462 Watts
- B . 650 Watts
- C . 838 Watts
- D . 1026 Watts
Which Dell PowerSwitch N-Series model supports the BGP and stack features?
- A . N1124T-ON
- B . N3224T-ON
- C . N3208PX-ON
- D . N2224PX-ON
A network administrator wants to lock down network access using port security.
What allows an administrator to specify a list of host MAC addresses that are allowed on a port?
- A . Static locking
- B . Sticky mode
- C . Switchport mode
- D . Dynamic locking
If Client B sends a packet to Client A, what is the highest level of the network hierarchy that the packet will transverse?

- A . Distribution
- B . Network
- C . Access
- D . Core
You need to configure OSPF on a DNOS 6 switch and have entered the following:
Switch-1(config)# ip routing –
Switch-1(config)# interface vlan 20
Switch-1(config-if-vlan20)# ip address 10.1.20.1 255.255.255.0
Switch-1(config)# router ospf –
Switch-1(config-router)# router-id 10.1.1.1
Based on the information referenced above, what is missing from the configuration?
- A . area 0 is missing from the ip routing command
- B . ip ospf area 0 is missing from the interface vlan 20 section
- C . router ospf is missing the routing instance
- D . area 0 is missing from the router-id command
Which command configures OSPF to advertise the network 10.10.0.0/16 to the Backbone Area?
- A . network 10.10.0.0 0.0.255.255 area 1
- B . network 10.10.0.0 255.255.0.0 area 0
- C . network 10.10.0.0 0.0.255.255 area 0
- D . network 10.10.0.0 255.255.0.0 area 1
How many ACLs are supported on a single interface in Dell EMC switches?
- A . One ACL in only one direction
- B . One ACL in either direction
- C . Two ACLs in either direction
- D . No limit of ACLS per interface