DELL EMC D-PCM-DY-23 Practice Exams
Last updated on Nov 16,2026- Exam Code: D-PCM-DY-23
- Exam Name: Dell PowerSwitch Campus Deploy 2023
- Certification Provider: DELL EMC
- Latest update: Nov 16,2026
What is the interaction between CDP, ISDP, and LLDP when communicating configuration information from a Dell EMC Campus networking switch to a Cisco VoIP phone?
- A . N-Series switches can be configured to use LLDP or CDP to communicate configuration information with Cisco devices
- B . N-Series switches can be configured to use only CDP to communicate configuration information with Cisco devices
- C . N-Series switches can be configured to use ISDP or CDP to communicate configuration information with Cisco devices
- D . N-Series switches can be configured to use ISDP or LLDP to communicate configuration information with Cisco devices
To which destination MAC address are MLAG peer-keepalive packets sent?
- A . 01:00:B5:00:00:00
- B . 01:00:C5:00:00:00
- C . B5:00:01:00:00:00
- D . C5:00:01:00:00:00
An administrator is attempting to configure MLAG on two pairs of stacked switches; however, the MLAG cannot be created.
What is the most likely reason for this issue?
- A . Stacked switches cannot perform MLAG functions
- B . Stacked switches are in a Daisy Chain topology
- C . Firmware on the MLAG stacks are at different versions
- D . Spanning tree is not enabled on the MLAG stacks
An administrator just finished configuring a Dell EMC N-Series switch. After rebooting the switch, the administrator notices that all the configuration settings just entered are gone.
Which command did the administrator fail to enter?
- A . Copy running-config startup-config
- B . Copy running-config backup-config
- C . Copy startup-config backup-config
- D . Copy startup-config running-config
What is the PoE source maximum power budget for a Class 3 end device?
- A . 12.95 watts
- B . 60 watts
- C . 30 watts
- D . 15.4 watts
A network administrator is setting up a Dell EMC N-Series PoE switch. The administrator is looking for a protocol that can deliver information to the end device that allows for refinement and fine tuning.
Which protocol option should be used?
- A . Flowcontrol
- B . dot1x
- C . LACP
- D . LLDP-MED
In order to alter a packet’s routing direction, which packet layers can policy-based routing use?
- A . Transport, Network, Link Layer, and Physical
- B . Link Layer, Physical, Presentation, and Session
- C . Network, Link Layer, Physical, and Session
- D . Application, Transport, Network, and Link Layer
A network administrator wants the traffic on different applications to take different network paths.
Which information can the administrator use to create a match to differentiate the application traffic when using policy-based routing?
- A . Physical port number
- B . TCP port number
- C . Destination IP address
- D . Source IP address
Based on the topology shown in the graphic, which ports are designated ports?

- A . Switch A, ports Te1/0/1 and Te1/0/2
- B . Switch B, ports Te1/0/3 and Te1/0/4
- C . Switch B port Te1/0/3 and Switch C port Te1/0/6
- D . Switch C, ports Te1/0/5 and Te1/0/6
Two switches are part of the same VRRP group with the following priorities configured:
– Switch1: Priority 110
– Switch2: Priority 90
– Switch2 is required to be the Master if interface GigabitEthernet 0/2 on Switch1 fails.
Which configuration should be part of the setup?
- A . Switch1(conf-if-vlan10)# vrrp 1 track interface vlan 20 decrement 100
Switch1(conf-if-vlan10)# no vrrp 1 preempt - B . Switch2(conf-if-vlan10)# vrrp 1 track interface vlan 20 decrement 100
Switch2(conf-if-vlan10)# no vrrp 1 preempt - C . Switch1(conf-if-vlan10)# vrrp 1 track interface vlan 20 decrement 100
Switch1(conf-if-vlan10)# vrrp 1 preempt - D . Switch2(conf-if-vlan10)# vrrp 1 track interface vlan 20 decrement 100
Switch2(conf-if-vlan10)# vrrp 1 preempt