Cisco 350-801 Practice Exams
Last updated on Nov 16,2026- Exam Code: 350-801
- Exam Name: Implementing and Operating Cisco Collaboration Core Technologies (CLCOR)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
Refer to the exhibit.

A collaboration engineer needs to replace the original, single NTP server that was configured during the initial install of a Cisco UCM server.
What is the first step to accomplish this task?
- A . Stop the NTP service on Cisco UCM.
- B . Enable NTP authentication for the new NTP server on Cisco UCM.
- C . Restart the NTP service on Cisco UCM.
- D . Delete the original NTP server from Cisco UCM.
What are two key features of the Expressway series? (Choose two.)
- A . IP to PSTN call connectivity
- B . B2B calls
- C . VPN connection toward the internal UC resources
- D . SIP header modification
- E . device registration over the Internet
After an engineer runs the utils ntp status command on the Cisco Unified Communications Manager publisher, the stratum value is 16.
Which issue can the Cisco Unified CM cluster experience?
- A . Unified CM sends an NTPv4 packet.
- B . Database replication is not synchronized on the Unified CM nodes.
- C . The cluster loses access to port 124 at the firewall.
- D . The date/time group on all phones defaults to the time zone of the engineer.
Refer to the exhibit.

A collaboration engineer configures Cisco UCM to act as a DHCP server.
What must be done next to configure the DHCP server?
- A . Restart the TFTP service under Cisco Unified Serviceability.
- B . Add a DHCP subnet to the DHCP server under Cisco UCM Administration.
- C . Add the new DHCP server to the primary DNS server.
- D . Restart the Cisco DHCP Monitor Service under Cisco Unified Serviceability.
When a user dials a number with a phone that is registered to the Cisco Unified Communications Manager, what is the default timeout before the number is sent?
- A . 15 seconds
- B . 5 seconds
- C . 10 seconds
- D . 3 seconds
Refer to the exhibit.

Cisco Unified Border Element is attempting to establish a call with Subscriber 1, but the call fails. Cisco Unified Border Element then retries the same call with Subscriber 2, and the call proceeds normally.
Which action resolves the issue?
- A . Verify that the Run On All Active Unified CM Nodes checkbox is enabled.
- B . Verify that the correct calling search space is selected for the Inbound Calls section.
- C . Verify that the Significant Digits field for Inbound Calls is set to All.
- D . Verify that the PSTN Access checkbox is enabled.
What are two characteristics of jitter in voice and video over IP communications? (Choose two.)
- A . The packets arrive at uniform time intervals.
- B . The packets arrive at varying time intervals.
- C . The packets never arrive due to tail drop.
- D . The packets arrive out of sequence.
- E . The packets arrive with frame errors.
A SIP phone has been configured in the system with MAC address 0030.96D2.D5CB. The phone retrieves the configuration file from the Cisco UCM.
Which naming format is the file that is downloaded?
- A . SEP0030407101980.cnf
- B . SIP0030407101980.cnf
- C . SIP003096D2D5CB.cnf.xml
- D . SEP003096D2D5CB.cnf.xml
An administrator troubleshoots call flows and suspects that there are issues with the dial plan.
Which tool enables a quick analysis of the dial plan and provides call flows of dialed digits?
- A . Dial Plan Analyzer
- B . Dialed Number Analyzer
- C . Cisco Dial Plan Analyzer
- D . Digit Analysis Analyzer
An end user at a remote site is trying to initiate an Ad Hoc conference call to an end user at the main site. The conference bridge is configured to support G.711.
The remote user’s phone only supports G.729.
The remote end user receives an error message on the phone: `Cannot Complete Conference Call. `
What is the cause of the issue?
- A . A software conference bridge is not assigned
- B . The remote phone does not have the conference feature assigned
- C . A Media Termination Point is missing
- D . The transcoder resource is missing