Cisco 300-510 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-510
- Exam Name: Implementing Cisco Service Provider Advanced Routing Solutions (SPRI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
Which command is used to enable BIDIR-PIM under global configuration mode for Cisco IOS XE Software?
- A . ip pim bidir ip
- B . multicast-routing
- C . ipv4 pim bidir-enable
- D . Ip pim bidlr-enable
Refer to the exhibit.

Routers R1 and R2 reside in AS 65530, which is multihomed to the Internet. A network engineer expects devices in the AS to use R2 to access the Internet, but they are using R1 as the exit point from the AS.
Which action corrects the problem?
- A . Add a sequence number to the route map to remove the implicit deny.
- B . Change the route map direction in the neighbor statement to out
- C . Configure the route map with a local preference of 200 or higher.
- D . Remove the neighbor statements from the address family configuration and activate the neighbor globally on R1.
B
Explanation:
Reference: https://community.cisco.com/t5/networking-blogs/bgp-as-path-prepending-configuration/ba-p/3819334
After changing the IP address on an IOS XR router, an engineer cannot ping the new address.
Which step did the engineer forget to complete?
- A . commit the configuration
- B . roll back the configuration
- C . save the running configuration
- D . merge the configuration
Refer to the exhibit.

CE1 and CE2 are iBGP neighbors in AS 65516. All traffic that exits AS 65516 must use the link from CE1 to PE1. CE1 is advertising a higher local preference to CE2, but traffic from CE2 still prefers the PE2 link.
Which action corrects the problem?
- A . Add the lower local-preference value on PE2 towards CE2.
- B . Configure CE1 to send routes to CE2 with a higher MED.
- C . Configure CE1 to send routes to CE2 with a higher weight.
- D . Add the next-hop self command to the CE1 neighbor statement for CE2.
D
Explanation:
Reference: https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/13753-25.html
Level 3 switch SW1 is part of an EIGRP enabled network located at the edge of an area. Cisco Express Forwarding and SSO are enabled on the router. A network engineer must minimize the downtime of data-transmit services in the network. HSRP group 2 has already been configured with standby preempt delay minimum 2 and standby timers 140.
Which additional action must the engineer take on SW1 to suppress routing flaps for 2 minutes?
- A . Configure timers standby 2 wait 2 under the HSRP group 2 configuration.
- B . Configure timers nsf route-hold 120 under the global EIGRP configuration.
- C . Configure timers nsf signal 2 under the global EIGRP IPv4 address family.
- D . Configure timers standby 2 coverage 120 under the HSRP group 2 configuration.
What is the role of a segment routing mapping server?
- A . It advertises a local SID mapping policy to all of the mapping clients
- B . It works with IGP instances to calculate the prefix-SIDs in the absence of a mapping policy
- C . It selects multiple mapping entries to create overlapping active mapping policies
- D . It reads and translates remotely received SIDs from other mapping servers to create SID mapping entries
Refer to the exhibit.

Which statement about this configuration is true?
- A . Router 1 sends and receives multiple best paths from neighbor 192.168.1.1
- B . Router 1 sends up to two paths to neighbor 192.168.1.1 for all routes
- C . Router 1 receives up to two paths from neighbor 192.168.1.1 for all routes in the same AS
- D . Router 1 receives only the best path from neighbor 192.168.1.1
Which statement about enabling segment routing for IGPs is true?
- A . Segment routing must first be enabled under then routing process and then globally
- B . Segment routing must first be enabled globally and then under the routing process
- C . Segment routing can be enabled only under the routing process
- D . Segment routing can be enabled only globally
B
Explanation:
Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/seg_routing/configuration/xe-16-6/segrt-xe-16-6-book/sr-ospfv2-node-sid.html
Refer to the exhibit.

Which two commands must the engineer configure for the company’s PIM-PIM network to enable Auto-RP mappings to be sent over the FastEthernet0/0 interface without affecting normal operation? (Choose two)
- A . enable auto-rp listener
- B . enable sparse-dense mode
- C . enable sparse-mode
- D . enable Auto-RP announcements
- E . enable dense mode
An engineer is working to implement segment routing protocol on the customer’s core network.
Which step should the engineer take before the segment routing is enabled and is running with BGP?
- A . Segment routing must be configured with ISIS.
- B . Segment routing must be configured with EIGRP.
- C . Explicit-null must be configured for all neighbors.
- D . MPLS must be configured.