Cisco 300-510 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-510
- Exam Name: Implementing Cisco Service Provider Advanced Routing Solutions (SPRI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
Refer to the exhibit.

IS-IS is the IGP for the network, where routers R1. R2 R3, and R4 are Level 1 routers in Area 12 and routers R5 and R6 are Level 2 routers m area 16 According to the network design router R1 must send traffic to R6 using R4 as its next hop To meet the requirement, a network engineer configured route filtering on R2 to prevent the route to R6 from being advertised from R2 However R1 is still using R2 as the next hop.
Which action must the engineer take to resolve the issue?
- A . Disable wide area metrics and use only cost to perform the route manipulation.
- B . Manipulate link costs to provide the desired routing through R4
- C . Move all routers into the same IS-IS area
- D . Configure routers R5 and R6 as Level 1/2 routers
Refer to the exhibit.

After maintenance to activate BGP neighbors connecting a new data center attached to R1, L3VPN customers attached to OSPF domain 100 lost connectivity to services in OSPF 200 and OSPF 300 However Unified MPLS services within OSPF 100 remain reachable.
Which action must the network engineer take to resolve the outage?
- A . Reset the BGP session between R1 and R2
- B . Activate BGP neighbors between the new data center and R2 and R3
- C . Establish new MPLS LSPs from R1 to R2, R3 and R4
- D . Raise the maximum prefix limit on R2 to 1560 or more
Refer to the exhibit.

A network engineer at a large ISP with an employee ID 4876 94 052 started to configure OSPF on two routers. The engineer notices that router 1 learned about network 20 20 20 0/24 from router 2, but router 2 did not learn about 10.10 10.0/24 from router 1 Layer 2 and Layer 3 connectivity are working between the two routers and the physical connection between the devices is functioning.
Which action must the engineer take to resolve the issue?
- A . Replace the router 1 OSPF network configuration with network 10.10.10.0 0.0.0.255 area 0.
- B . On router 1 configure a route map with a distribution list for the 10 10.10 0/24 network.
- C . Replace the router 2 OSPF network configuration with network 10.10.10.0 0.0.0.255 area
- D . On router 2 configure a route map with a distribution list for the 101010 0/24 network
Which feature is used in multicast routing to prevent loops?
- A . STP
- B . inverse ARP
- C . RPF
- D . split horizon
Refer to the exhibit.

A network engineer configured three new PE routers to expand the network. The new routers run in the IS-IS routing protocol and reside in the data center in the same exchange as the existing routers. However, the network is now experiencing suboptimal routing. The Layer 2 configuration and VLANs are configured correctly to provide segregation between networks, but the Level 1 routes are not being converted to Level 2 routes.
Which action resolves the issue?
- A . On Router 1, redistribute the routes into IGP.
- B . On Router 1, summarize internal routes between areas.
- C . On Router 2, redistribute the routes into IGP.
- D . On Router 2. summarize internal routes between areas.
Refer to the exhibit.

A network operator is working to filter routes from being advertised that are covered under an aggregate announcement. The receiving router of the aggregate announcement block is still getting some of the more specific routes plus the aggregate.
Which configuration change ensures that only the aggregate is announced now and in the future if other networks are to be added?
- A . Configure the summary-only keyword on the aggregate command
- B . Set each specific route in the AGGRO policy to drop instead of suppress-route
- C . Filter the routes on the receiving router
- D . Set each specific route in the AGGRO policy to remove instead of suppress-route
RPL has several fundamental capabilities that differ from those present in configurations oriented to traditional route maps Routing policy language introduces the notion of sets.
Which group of set types is valid in RPL?
- A . acl-path-set community-set pre-community-set prefix-set and bgp-set
- B . as-path-set community-set. extcommunity-set prefix-set and rd-set
- C . access-control-set, community-set post-community-set pre-prefix-set and routed-set
- D . route-path-set, community-set in-community-set prefix-set and rd-set
Refer to the exhibit.

BGP is running on the network, and CE1 currently prefers routes to the internet via PE 1 A network engineer must manipulate the BGP routes that CE1 receives from PE2 to be more desirable The engineer configured a route map using MED and applied it on CE1 outbound from PE2. However, after a BGP soft reset. PE1 is still preferred.
Which action must the engineer take so that PE2 is chosen as the next hop?
- A . Update the route map to use only weight to manipulate the path.
- B . Configure the route map with MED and local preference to manipulate the route outbound
- C . Apply the route map on CE1 In the inbound direction.
- D . Configure the route map with AS path prepend to manipulate the AS path to exit the autonomous system
Which two characteristics unique to SSM when compared to ASM are true? (Choose two.)
- A . It uses SPT switchover
- B . It uses (*,G) exclusively
- C . It uses IGMPv3
- D . It uses RP
- E . It uses (S,G) exclusively
What are two major differences between OSPF and IS-IS routing protocols? (Choose two.)
- A . OSPF uses IP protocol 89 foe encapsulation and IS-IS uses an IEEE 802 3 standard-based protocol foe encapsulation
- B . The OSPF default administrative distance is 115 and the default administrative distance for IS-IS is 110
- C . The OSPF DR role can be pre-empted only when the active DR goes down, but the IS-IS DR role can be taken by a router with higher priority at any time
- D . OSPF partially refreshes the LSA database every 30 minutes, and IS-IS refreshes the complete database table every 60 minutes
- E . An OSPF-enabled router is part of only one area but an IS-IS-enabled router is part of multiple areas