Cisco 300-425 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-425
- Exam Name: Designing Cisco Enterprise Wireless Networks (ENWLSD)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
A wireless engineer is performing a post verification of a wireless network.
Which two metrics does the engineer verify to ensure that the wireless network can support voice services? (Choose two.)
- A . The coverage area must have a noise floor that does not exceed -87 dBm.
- B . The client device must have at least an -67 dBm RSSI.
- C . The rate of retransmitted packets must be 15 percent or below.
- D . The rate of retransmitted packets must be 20 percent or below.
- E . The client device must have at least an -65 dBm RSSI.
B,C
Explanation:
![]()
A company has 10 access point licenses available on their backup Cisco WLC and their primary Cisco WLC is at full capacity, 5 access points are set to high failover priority and 7 access points are set to critical failover priority. During a failure, not all critical access points failed over to the backup Cisco WLC.
Which configuration is the cause of this issue?
- A . The high priority access point is oversubscribed.
- B . network ap-priority is set to enable.
- C . The critical priority access point count is oversubscribed.
- D . network ap-priority is set to disable.
D
Explanation:
https://www.ciscolive.com/c/dam/r/ciscolive/emea/docs/2016/pdf/BRKCOL-2275.pdf
An engineer needs a wireless design to provide redundancy for APs at remote sites that are connected to Cisco 3504 Wireless LAN Controllers. The central Cisco 5520 Wireless LAN Controller supports 2000 APs and has 1975 access points associated to it. The engineer decides that not all APs at the remote sites must remain functional in the event of a failure.
How does the engineer ensure that the most important access points at the remote sites remain online while not impacting the main site?
- A . Enable Global AP Fail over Priority, set the 1975 APs to a priority of "high", and set the 25 most important APs at the remote sites to "critical".
- B . Enable AP Fallback Mode, set the 1975 APs to a priority of "high", and set the 25 most important APs at the remote sites to "critical".
- C . Enable Global AP Fail over Priority, leave the 1975 APs at the default priority, and set the most important APs at the remote sites to "low".
- D . Enable AP Fallback Mode, leave the 1975 APs at the default priority, and set the most important APs at the remote sites to "high".
An engineer is working for a manufacturing company that has a centralized deployment model. Guests at headquarters need wireless access for presentations, demonstrations, and sharing of information. The engineer must provide external users with secure guest access by connecting to anchor controllers on the DMZ. Auto-Anchor Mobility has been selected in the mobility group to accomplish it. Both anchors are configured as part of the mobility group for HQ.
Which design approach ensures that clients connect to the primary controller first and are pushed to the secondary if the primary fails?
- A . Set the Anchor priority for the primary controller to 1.
- B . Set the Anchor priority for the secondary controller to 1.
- C . Configure ECMP but weigh the cost to be higher to go to the primary.
- D . Configure ECMP but weigh the cost to be higher to go to the secondary.
An engineer added an AP to a deployment after a post-installation site survey. The engineer then notices an increase in co-channel interference and retransmissions.
Which two features help mitigate the issue? (Choose two.)
- A . Cisco Compatible Extensions
- B . Transmit Power Control
- C . Enhanced Distributed Channel Access
- D . Coverage Hole Detection
- E . Dynamic Channel Assignment
What is required to support Intercontroller Roaming in a Cisco wireless architecture?
- A . Mobility Groups
- B . Same RF Group
- C . Layer 3 connectivity
- D . Uniform AP models
A customer is looking for a network design with Cisco Hyperloctation using AP4800 for location tracking via a custom mobile app Issues appeared in the past with refresh rates for location updates.
What needs to be implemented to meet these requirements?
- A . Cisco CMX SDK in the location app
- B . redundant CMX and fetch location in round-robin fashion.
- C . device Bluetooth via the app
- D . Cisco FastLocate technology
What is the recommended cell overlap when designing a wireless network for Cisco Hyperlocation?
- A . 20%
- B . 30%
- C . 40%
- D . 50%
A
Explanation:
![]()
An engineer is designing a mesh wireless network.
The network must full these requirements:
• bridge mode APs must be used
• WPA2-PSK
• minimize wireless traffic tunneled to the WLC
- A . bridge RAP
- B . Flex + Bridge
- C . FlexConnect
- D . bridge MAP
Why is 802.11a connectivity reduced in an X-ray room?
- A . X-rays create significant non-Wi-Fi interference on the 802.11a band.
- B . X-rays impact the 802,11a UNll-2 channels that cause access points to dynamically change channels.
- C . X -rays within these rooms cause multipath issues.
- D . X-ray rooms exhibit increased signal attenuation.
D
Explanation:
portable X-ray machines, sending high-resolution images, sometimes in real time, echography machines, and electrocardiography [ECG] machines). These devices may also use the same spectrum as Wi-Fi but with other protocols and, therefore, become sources of interference for your system.