Cisco 300-425 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-425
- Exam Name: Designing Cisco Enterprise Wireless Networks (ENWLSD)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
A network engineer is working on a design for a wireless network that must support data, voice, and location services.
To support these services, which access point placement must the engineer use?
- A . corner only
- B . perimeter and corner
- C . perimeter only
- D . indoor and outdoor
B
Explanation:
![]()
During a post-deployment site Survey, issues are found with non wi-Fi interference.
What should the engineer use to identify the source of the Interference?
- A . Network analysis module
- B . Wireless intrusion prevention
- C . Wireshark
- D . Cisco spectrum expert
An engineer must configure the virtual IP address on multiple controllers in a mobility group.
Which rule must the engineer follows to ensure proper roaming?
- A . Ensure that the DNS entry is tied to the virtual IP address of the WLC.
- B . Use a unique IP address for each WLC.
- C . Ensure that the DNS Host Name field is defined.
- D . Use the same IP address for each WLC.
D
Explanation:
![]()
A high-density wireless network is designed.
Which Cisco WLC configuration setting must be incorporated in the design to encourage clients to use the 5 GHz spectrum?
- A . RRM
- B . Cisco centralized key management
- C . Band select
- D . Load balancing
During a meeting to gather the requirements for a new Wi-Fi network design, the customer requests that to connect.
Which affect does this have to the wireless network?
- A . bigger channel width
- B . lower throughput
- C . 2.4 GHz signal congestion
- D . higher RF re ection
An engineer must create data link redundancy for the company’s Cisco Wireless LAN controller. The engineer has decided to configure LAG-based redundancy instead of port-based redundancy.
Which three features of LAG-based redundancy influenced this decision? (Choose three.)
- A . Packets are always sent out on the same port they are received on.
- B . All interface traffic passes as long as one port is up.
- C . The same port has multiple untagged dynamic interfaces.
- D . Interface connection to two separate nonstacked switches is available.
- E . Full bandwidth of all links is available.
- F . Ports are grouped into multiple LAGs.
A,B,F
Explanation:
https://community.cisco.com/t5/wireless-mobility-documents/lag-link-aggregation/ta-p/3128669
What is the attenuation value of a human body on a wireless signal?
- A . 3 dB
- B . 4 dB
- C . 6 dB
- D . 12 dB
A
Explanation:
Signal AttenuationSignal attenuation or signal loss occurs even as the signal passes through air. The loss of signal strength is more pronounced as the signal passes through different objects. A transmit power of 20 mW is equivalent to 13 dBm. Therefore, if the transmitted power at the entry point of a plasterboard wall is at 13 dBm, the signal strength is reduced to 10 dBm when exiting that wall. This table shows the likely loss in signal strength caused by various types of objects.
Signal Attenuation Caused By Various Types of Objects
Object in Signal Path
Signal Attenuation through Object
Plasterboard wall
3 dB
Glass wall with metal frame
6 dB
Cinder block wall
4 dB
Office window
3 dB Metal door
6 dB
Metal door in brick wall
12 dB Human body
3 dB
Each site surveyed has different levels of multipath distortion, signal loses, and signal noise. Hospitals are typically the most challenging environment to survey due to high multipath distortion, signal losses and signal noise. Hospitals take longer to survey, require a denser population of access points, and require higher performance standards. Manufacturing and shop floors are the next hardest to survey. These sites generally have metal siding and many metal objects on the floor, which result in reflected signals that recreate multipath distortion. Office buildings and hospitality sites generally have high signal attenuation but a lesser degree of multipath distortion. https://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/71642-vocera-deploy-guide.html
A technician connects a Cisco Aironet 3700 Series access point to a switch and realizes that the AP is coming up with 3×3 MIMO.
Which reason explains this behavior?
- A . A redundant power supply is unavailable on the switch.
- B . The switch is 802.3af capable.
- C . The AP is getting power from a power injector.
- D . The switch is PoE+ capable.
D
Explanation:
![]()
![]()
Which three considerations are critical when planning for voice over wireless roaming? (Choose three)
- A . Client density per AP
- B . Minimum RSSI thresholds
- C . AP placement for optimal coverage
- D . Use of 802.1X + EAP for authentication
- E . Seamless Layer 2 and Layer 3 roaming capabilities
An engineer is designing a wireless network to support high availability. The network will need to support the total number of APs and client SSO. Live services should continue to work without interruption during the failover.
Which two requirements need to be incorporated into the design to meet these needs? (Choose two.)
- A . redundant WLC
- B . controller high availability pair with one of the WLCs having a valid AP count license
- C . 10 sec RTT
- D . back-to-back direct connection between WLCs
- E . WLC 7.5 code or more recent
B,D
Explanation:
https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/7-5/High_Availability_DG.html#pgfId-44074