Cisco 300-425 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-425
- Exam Name: Designing Cisco Enterprise Wireless Networks (ENWLSD)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
A school deploys a Cisco wireless infrastructure in its classrooms to support a high density of mobile devices. The network administrator wants to bond channels in groups of two and only allow APs to send 802.11 management frames at 24 MB.
What should be included in the design to accomplish this objective?
- A . Set the channel width for 802.11b to 40 MHz and set data rates to 24 MB and Mandatory.
- B . Set the channel width for 802.11a to 40 MHz and set data rates to 24 MB and Supported.
- C . Set the channel width for 802.11a to 40 MHz and set data rates to 24 MB and Mandatory.
- D . Set the channel width for 802.11b to 40 MHz and set data rates to 24 MB and Supported.
Refer to the exhibit.

An enterprise has offices spread around the globe. The APs are connected to different controllers installed in separate datacenters. The IT team wants to allow clients to roam from controllers in group ABC to controllers in group XYZ.
Which feature must be incorporated in the design to accomplish this task?
- A . switch peer group
- B . workgroup bridge
- C . mDNS gateway
- D . mobility lists
A network consultant is designing a wireless network for a government agency. The customer requires high security between any device
communication. The design includes AireOS, Cisco IOS-XE controllers, and Cisco 4800 Series APs.
Which requirement must be met to enhance the mobility group security?
- A . Use a different group name for each mobility member.
- B . Enable MIC authentication between the mobility group members.
- C . Enable Mobility Encryption on the network.
- D . Use a complex group name for the mobility group.
An engineer is designing a solution where guests terminate on an anchor controller in the DMZ. The engineer is having issues and wants to test connectivity between members of a mobility group.
Which command must be issued to test whether a mobility control packet is able to be reached over the management interface?
- A . show logging
- B . mapping
- C . mapping
- D . tracert
Which technology is critical for location tracking accuracy in a Cisco wireless environment?
- A . AoA
- B . MU-MIMO
- C . Beamforming
- D . QoS
An enterprise is using a Cisco AireOS controller and Wi-Fi 6 APs. The controller is installed in the head office, and the employees primarily use Apple OS devices. The APs broadcast WLAN ENT-WLAN406558520-1 for the employees and a guest WLAN with similar naming.
What needs to be enabled on the controller to optimize roaming?
- A . Aggregated Probe Response Optimization
- B . Fast SSID Changing
- C . Load Balancing Window
- D . Client Timers
Which statement about the 9800 Series Wireless Controller mobility tunnel on a Cisco Catalyst 9800 controller is true?
- A . It is an IPsec tunnel with control path only.
- B . It is a CAPWAP tunnel with data path only.
- C . It is a CAPWAP tunnel with control path and data path.
- D . It is an IPsec tunnel with control path and data path.
C
Explanation:
![]()
https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/config-guide/b_wl_16_10_cg/mobility.html
An engineer is trying to configure the APs installed in a new auditorium to use 40 MHz channels with high data rates and lower TX power. The APs in the building hallway must use lower-density design settings configured for the rest of the building.
Which two configurations achieve this design? (Choose two.)
- A . TPC
- B . DCA
- C . AP group
- D . RRM
- E . RF protocol
Which statement about AP failover priority for access points when configured with priority 1 or 4 is true?
- A . When configured with priority 1, the access point is assigned with the highest priority level and it is marked as critical. This access point fails over before other access points with the lower priority when there is primary controller failure.
- B . When configured with priority 4, the access point is assigned with the highest priority level and it is marked as critical. This access point fails over before other access points with the lower priority
when there is primary controller failure. - C . When configured with priority 4, the access point is assigned with the lowest priority level and it is marked as low. This access point fails over after other access points with the higher priority when there is primary controller failure.
- D . When configured with priority 1, the access point is assigned with the medium priority level and it is marked as medium. This access point fails over after other access points with the higher priority when there is primary controller failure.
B
Explanation:

Based on a wireless network design, an engineer configured a primary and secondary controller for
their APs. A power interruption caused the primary Cisco WLC to go down, and, as expected, all APs joined the secondary controller. When the primary controller came back up, all the APs remained joined to the secondary controller.
Which approach must the engineer take for the APs to move back to the primary?
- A . Set AP Fail over Priority to 4 on each AP.
- B . Set AP Fallback to Enabled on the secondary controller.
- C . Set AP Fallback to Enabled on the primary controller.
- D . Set AP Fail over Priority to Critical globally.