Cisco 300-410 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-410
- Exam Name: Implementing Cisco Enterprise Advanced Routing and Services (ENARSI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
Refer to the exhibit.

An engineer notices a connectivity problem between routers R1 and R2. The frequency of this problem is high during peak business hours.
Which action resolves the issue?
- A . Increase the MTU on the interfaces that connect R1 and R2.
- B . Increase the available bandwidth between R1 and R2.
- C . Decrease the EIGRP keepallve and hold down timers on R1 and R2.
- D . Set static EIGRP neighborship between R1 and R2.
A network engineer is investigating a flapping (up/down) interface issue on a core switch that is synchronized to an NTP server. Log output currently does not show the time of the flap.
Which command allows the logging on the switch to show the time of the flap according to the clock on the device?
- A . service timestamps log uptime
- B . clock summer-time mst recurring 2 Sunday mar 2:00 1 Sunday nov 2:00
- C . service timestamps log datetime localtime show-timezone
- D . clock calendar-valid
C
Explanation:
By default, Catalyst switches add a simple uptime timestamp to logging messages. This is a cumulative counter that shows the hours, minutes, and seconds since the switch has been booted up
Refer to exhibit.

Routing protocols are mutually redistributed on R3 and R1. Users report intermittent connectivity to services hosted on the 10.1.1.0/24 prefix. Significant routing update changes are noticed on R3 when the show ip route profile command is run.
How must the services be stabilized?
- A . The issue with using BGP must be resolved by using another protocol and redistributing it into EIGRP on R3
- B . The routing loop must be fixed by reducing the admin distance of iBGP from 200 to 100 on R3
- C . The routing loop must be fixed by reducing the admin distance of OSPF from 110 to 80 on R3
- D . The issue with using iBGP must be fixed by running eBGP between R3 and R4
B
Explanation:
After redistribution, R3 learns about network 10.1.1.0/24 via two paths:
+ Internal BGP (IBGP): advertised from R4 with AD of 200 (and metric of 0)
+ OSPF: advertised from R1 with AD of 110 (O E2) (and metric of 20)
Therefore R3 will choose the path with the lower AD via OSPF But this is a looped path which is received from R3 -> R2 -> R1 -> R3. So when the advertised route from R4 is expired, the looped path is also expired soon and R3 will reinstall the main path from R4. This is the cause of intermittent connectivity. In order to solve this issue, we can lower the AD of iBGP to a value which is lower than 110 so that it is preferred over OSPF-advertised route.
Which statement about route distinguishers in an MPLS network is true?
- A . Route distinguishers allow multiple instances of a routing table to coexist within the edge router.
- B . Route distinguishers are used for label bindings.
- C . Route distinguishers make a unique VPNv4 address across the MPLS network.
- D . Route distinguishers define which prefixes are imported and exported on the edge router.
Refer to the exhibit.

Refer to the exhibit. An engineer configured SNMP traps to record spoofed packets drop of more than 48000 a minute on the ethernet0/0 interlace. During an IP spoofing attack, the engineer noticed that no notifications have been received by the SNMP server.
Which configuration resolves the issue on R1?
- A . ip verity unicast notification threshold 48000
- B . ip verify unicast notification threshold 8000
- C . ip verify unicast notification threshold 800
- D . ip verify unicast notification threshold 80
Which transport layer protocol is used to form LDP sessions?
- A . UDP
- B . SCTP
- C . TCP
- D . RDP
C
Explanation:
LDP multicasts hello messages to a well-known UDP port (646) in order to discover neighbors. Once the discovery is accomplished, a TCP connection (port 646) is established and the LDP session begins. LDP keepalives ensure the health of the session. Thanks to the LDP session, LDP messages create the label mappings required for a FEC. Withdraw messages are used when FECs need to be torn down.
Refer to the exhibit.

After an engineer configured a new Cisco rouler as a DHCP server, users reponed two primary issues:
✑ Devices in the HR subnet have intermittent connectivity problems.
✑ Workstations in the LEGAL subnet cannot obtain IP addresses.
Which configurations must the engineer apply to ROUTER_1 to restore connectivity for the affected devices?


- A . Option A
- B . Option B
- C . Option C
- D . Option D
Refer to the exhibit.

Which action ensures that 10 10 10 0/24 reaches 10 10 20 0/24 through the direct link between R1 and R2?
- A . Configure R1 and R2 LAN links as nonpassive.
- B . Configure R1 and R2 links under area 1
- C . Configure OSPF link cost to 1 between R1 and R2
- D . Configure OSPF path cost to 3 between R1 and R2
Refer to the exhibit.

An organization is installing a new L3 MPLS link to establish DM VPN Phase 2 tunnels between the hub and two spoke routers.
Which additional configuration should the engineer implement on each device to achieve optimal routing between the spokes?
A)

B)

C)

D)

- A . Option
- B . Option
- C . Option
- D . Option
What does the MP-BGP OPEN message contain?
- A . MPLS labels and the IP address of the router that receives the message
- B . the version number and the AS number to which the router belongs
- C . IP routing information and the AS number to which the router belongs
- D . NLRI, path attributes, and IP addresses of the sending and receiving routers