Cisco 300-410 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-410
- Exam Name: Implementing Cisco Enterprise Advanced Routing and Services (ENARSI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
Refer to the exhibit.

An engineer has configured R1 as EIGRP stub router. After the configuration, router R3 failed to reach to R2 loopback address.
Which action advertises R2 loopback back into the R3 routing table?
- A . Add a static route for R2 loopback address in R1 and redistribute it to advertise to R3.
- B . Use a leak map on R1 that matches the required prefix and apply it with the distribute list command toward R3.
- C . Use a leak map on R3 that matches the required prefix and apply it with the EIGRP stub feature.
- D . Add a static null route for R2 loopback address in R1 and redistribute it to advertise to R3.
B
Explanation:
The EIGRP stub feature is useful to prevent unnecessary EIGRP queries and to filter some routes that
you advertise.
What if you want to configure your router as a stub router but still make an exception to some routes that it advertises? That is possible with the leak-map feature.
This is how to configure leak-map in this question:
R1(config)#ip access-list standard R2_L0
R1(config-std-nacl)#permit host 2.2.2.2
R1(config)#route-map R2_L0_LEAK
R2(config-route-map)#match ip address R2_L0
R1(config)#router eigrp 1
R1(config-router)#eigrp stub leak-map R2_L0_LEAK
Refer to the exhibit.

An engineer configured route exchange between two different companies for a migration project EIGRP routes were learned in router C but no OSPF routes were learned in router A.
Which configuration allows router A to receive OSPF routes?
- A . (config-router-af)#redistribute ospf 10 1000000 10 255 1 1500
- B . (config-routeraf-topology)#redistribute ospf 10 metric 1000000 10 255 1 1500
- C . (config-router-af-topology)#redistribute connected
- D . (config-router-af-topology )£no redistribute ospf 10 match external 1 external 2 metric 1000000 10 255 1 1500
Which command allows traffic to load-balance in an MPLS Layer 3 VPN configuration?
- A . multi-paths eibgp 2
- B . maximum-paths 2
- C . Maximum-paths ibgp 2
- D . multi-paths 2
C
Explanation:
Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/5_x/nx-os/mpls/configuration/guide/mpls_cg/mp_vpn_multipath.html
A customer is running an mGRE DMVPN tunnel over WAN infrastructure between hub and spoke sites. The existing configuration allows NHRP to add spoke routers automatically to the multicast NHRP mappings. The customer is migrated the network from IPv4 to the IPv6 addressing scheme for those spokes’ routers that support IPv6 and can run DMVPN tunnel over the IPv6 network.
Which configuration must be applied to support IPv4 and IPv6 DMVPN tunnel on spoke routers?
- A . Tunnel mode ipv6ip 6to4
- B . Tunnel mode ipv6ip isatap
- C . Tunnel mode ipv6ip auto-tunnel
- D . Tunnel mode ipv6ip 6rd
A network administrator cannot connect to a device via SSH.
The line vty configuration is as follows:

Which action resolves this issue?
- A . Increase the session timeout
- B . Change the stopbits to 10.
- C . Configure the transport input SSH
- D . initialize the SSH key
What are two characteristics of VRF instance? (Choose two.)
- A . All VRFs share customers routing and CEF tables .
- B . An interface must be associated to one VRF.
- C . Each VRF has a different set of routing and CEF tables
- D . It is defined by the VPN membership of a customer site attached to a P device.
- E . A customer site can be associated to different VRFs
B,C
Explanation:
Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipswitch_cef/configuration/xe-3s/isw-cef-xe-3s-book/isw-cef-basic-config.html
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/mp_l3_vpns/configuration/15-s/mp-l3-vpns-15-s-book/mp-bgp-mpls-vpn.pdf
The summary route is not shown in the RouterB routing table after this below configuration on Router_A.

Which Router_A configuration resolves the issue by advertising the summary route to Router B?

- A . Option A
- B . Option B
- C . Option C
- D . Option D
Which statement about MPLS LDP router ID is true?
- A . If not configured, the operational physical interface is chosen as the router ID even if a loopback is configured.
- B . The loopback with the highest IP address is selected as the router ID.
- C . The MPLS LDP router ID must match the IGP router ID.
- D . The force keyword changes the router ID to the specified address without causing any impact.
B
Explanation:
Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/mp_ldp/configuration/12-4m/mp-ldp-12-4mbook.pdf
Refer to the exhibit.


The network administrator must configure Cape Town to reach Dubai via Tokyo based on the speeds provided by the service provider. It was noticed that Cape Town is reaching Dubai directly and failed to meet the requirement.
Which configuration fixes the issue?
A)

B)

C)

D)

- A . Option
- B . Option
- C . Option
- D . Option
Refer to the exhibit.

Which action resolves the failed authentication attempt to the router?
- A . Configure aaa authorization login command on line vty 0 4
- B . Configure aaa authorization login command on line console 0
- C . Configure aaa authorization console global command
- D . Configure aaa authorization console command on line vty 0 4
C
Explanation:
In the debug output, we see that the Authorization (not Authentication) failed so we need to correct the authorization. In order to enable authorization, we must use the global command “aaa authorization console” first.
Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/security/a1/sec-a1-cr-book/sec-cr-a1.html