Cisco 300-410 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-410
- Exam Name: Implementing Cisco Enterprise Advanced Routing and Services (ENARSI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
Which MPLS value is combined with the IP prefix to convert to a VPNv4 prefix?
- A . 16-byte Route Distinguisher
- B . 8-byte Route Target
- C . 16-byte Route Target
- D . 8-byte Route Distinguisher
Refer to the exhibit.

R1 uses SP1 as the primary path. A network engineer must force all SSH traffic generated from R1 toward SP2.
Which configuration accomplishes the task?
A)

B)

C)

D)

- A . Option
- B . Option
- C . Option
- D . Option
Refer to the exhibit.

R1 is connected with R2 via GigabitEthernet0/0, and R2 cannot ping R1.
What action will fix the issue?
- A . Fix route dampening configured on the router.
- B . Replace the SFP module because it is not supported.
- C . Fix IP Event Dampening configured on the interface.
- D . Correct the IP SLA probe that failed.
C
Explanation:
![]()
Refer to the exhibit.

An engineer cannot determine the time of the problem on R1 due to a mismatch between the router local clock and legs.
Which command synchronizes the time between new log entries and the local clock on R1?
- A . service timestamps debug datetime msec show.timezone
- B . service timestamps log datetime locatetime msec
- C . service timestamps datebug datetime localtime msec
- D . service timestamps log datetime msec show-timezone
Refer to the exhibit.

An engineer configured NetFlow on R1, but the flows do not reach the NMS server from R1.
Which configuration resolves this Issue?

- A . Option A
- B . Option B
- C . Option C
- D . Option D
Refer to the exhibit.

An administrator must configure the router with OSPF for IPv4 and IPv6 networks under a single process. The OSPF adjacencies are not established and did not meet the requirement.
Which action resolves the issue?
- A . Replace OSPF process 10 on the interface with OSPF process 1, and configure an additional router ID with IPv6 address.
- B . Replace OSPF process 10 on the interface with OSPF process 1, for the VPv6 addressma nd remove process route ID with IPv6 address.
- C . Replace OSPF process 10 on the interface with OSPF process 1, and remove process 10 from the global configuration.
- D . Replace OSPF process 10 on the interface with OSPF process 1 for the IPv4 address, and remove process 10 from the global configuration.
Refer to the exhibit.

Router R4 is configured correctly with default OSPF values. A network engineer configured R7 for OSPF. R7 must not be elected as a DR for the segment between R4-R7. The adjacency between R4 and R7 failed to form.
Which configuration resolves the issue?

- A . Option A
- B . Option B
- C . Option C
- D . Option D
Refer to the exhibit.

An engineer must configure a LAN-to-LAN IPsec VPN between R1 and the remote router .
Which IPsec Phase 1 configuration must the engineer use for the local router?
- A . crypto isakmp policy 5
authentication pre-share
encryption 3des
hash sha
group 2
!
crypto isakmp key cisco123 address 200.1.1.3 - B . crypto isakmp policy 5
authentication pre-share
encryption 3des
hash md5
group 2
!
crypto isakmp key cisco123 address 200.1.1.3 - C . crypto isakmp policy 5
authentication pre-share
encryption 3des
hash md5
group 2
!
crypto isakmp key cisco123 address 199.1.1.1 - D . crypto isakmp policy 5
authentication pre-share
encryption 3des
hash md5
group 2
!
crypto isakmp key cisco123! address 199.1.1.1
A
Explanation:
In the “crypto isakmp key … address ” command, the address must be of the IP address of the other end (which is 200.1.1.3 in this case) so Option A and Option B are correct. The difference between these two options are in the hash SHA or MD5 method but both of them can be used although SHA is better than MD5 so we choose Option A the best answer.
Note: Cisco no longer recommends using 3DES, MD5 and DH groups 1, 2 and 5.
Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_conn_imgmt/configuration/xe-16-5/sec-ipsec-management-xe-16-5-book/sec-ipsec-usability-enhance.html
In a DMVPN network, the Spoke1 user observed that the voice traffic is coming to Spoke2 users via the hub router.
Which command is required on both spoke routers to communicate directly to one another?
- A . ip nhrp map dynamic
- B . ip nhrp shortcut
- C . ip nhrp nhs multicast
- D . ip nhrp redirect
Refer to the exhibit.

Router R1 peers with two ISPs using static routes to get to the internet. The requirement is that R1 must prefer ISP-A under normal circumstances and failover to ISP-B if the connectivity to ISP-A is lost. The engineer observes that R1 is load balancing traffic across the two ISPs.
Which action resolves the issue by sending traffic to ISP-A only with failover to ISP-B?
- A . Configure OSPF between R1. ISP-A. and ISP-B for dynamic failover if any ISP link to R1 fails
- B . Configure two static routes on R1. one pointing to ISP-A and another pointing to ISP- B with 222 admin distance
- C . Change the bandwidth of the interface on R1 so that interface to ISP-A has a higher value than the interface to ISP-B
- D . Configure two static routes on R1. one pointing to ISP-B with more specific routes and another pointing to ISP-A with summary routes