Cisco 300-410 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-410
- Exam Name: Implementing Cisco Enterprise Advanced Routing and Services (ENARSI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
Refer to the exhibit.

An engineer must ensure that R3 sees only type 1 and 2 LSAs in area 1.
Which command must the engineer apply on R2?
- A . Area 1 stub nssa
- B . Area 1nssa no-summary
- C . Area a stub no-summary
- D . Area 1 stub
Which feature is used by LDP in the forwarding path within the MPLS cloud?
- A . IP forwarding
- B . TTL
- C . TDP
- D . LSP
Which protocol does MPLS use to support traffic engineering?
- A . Tag Distribution Protocol (TDP)
- B . Resource Reservation Protocol (RSVP)
- C . Border Gateway Protocol (BGP)
- D . Label Distribution Protocol (LDP)
B
Explanation:
![]()
Refer to the exhibit.

AS65510 iBGP is configured for directly connected neighbors. R4 cannot ping or traceroute network 192 168.100.0/24.
Which action resolves this issue?
- A . Configure R4 as a route reflector server and configure R1 as a route reflector client
- B . Configure R1 as a route reflector server and configure R2 and R3 as route reflector clients
- C . Configure R4 as a route reflector server and configure R2 and R3 as route reflector clients.
- D . Configure R1 as a route reflector server and configure R4 as a route reflector client
D
Explanation:
A route received from one iBGP peer will NOT be advertised to another iBGP peer. Therefore R4 could not receive advertisement for network 192.168.100.0/24. We can overcome this BGP limitation by configuring R1 as a route reflector server and R4 as a route reflector client so that R1 sends advertisements for R4.
Refer to the exhibit.

An engineer must redistribute networks 192.168.10.0/24 and 192.168.20.0/24 into OSPF from EIGRP. where the metric must be added when traversing through multiple hops to start an external route of 20 The engineer notices that the external metric is fixed and does not add at each hop.
Which configuration resolves the issue?


- A . Option A
- B . Option B
- C . Option C
- D . Option D
Refer to the exhibit.


The network engineer configured the summarization of the RIP routes into the OSPF domain on R5 but
still sees four different 172.16.0.0/24 networks on R4.
Which action resolves the issue?
- A . R5(config)#router ospf 1
R5(config-router)#no area
R5(config-router)#summary-address 172.16.0.0 255.255.252.0 - B . R4(config)#router ospf 99
R4(config-router)#network 172.16.0.0 0.255.255.255 area 56
R4(config-router)#area 56 range 172.16.0.0 255,255.255.0 - C . R4(config)#router ospf 1
R4(config-router)#no area
R4(config-router)#summary-address 172.16.0.0 255.255.252.0 - D . R5(config)#router ospf 99
R5(config-router)#network 172.16.0.0 0.255.255.255 area 56
R5(config-router)#area 56 range 172.16.0.0 255.255.255.0
A
Explanation:
Area 36 is a NSSA so R5 is an ASBR so we can summarize external routes using the “summaryaddress”
command. The command “area area-id range” can only be used on ABR so it is not correct.
The summarization must be done on the ASBR which is R5, not R4 so the correct answer must be started with “R5(config)#router ospf 1”.
Note: The “no area” command is used to remove any existing “area …” command (maybe “area 56 range …” command).
Refer to the exhibit.

An IPv6 network was newly deployed in the environment and the help desk reports that R3 cannot SSH to the R2s Loopback interface.
Which action resolves the issue?
- A . Modify line 10 of the access list to permit instead of deny.
- B . Remove line 60 from the access list.
- C . Modify line 30 of the access list to permit instead of deny.
- D . Remove line 70 from the access list.
Refer to the exhibit.

The network administrator has configured the Customer Edge router (AS 64511)
to send only summarized routes toward ISP-1 (AS 100) and ISP-2 (AS 200).
router bgp 64511
network 172.16.20.0 mask 255.255.255.0
network 172.16.21.0 mask 255.255.255.0
network 172.16.22.0 mask 255.255.255.0
network 172.16.23.0 mask 255.255.255.0
aggregate-address 172.16.20.0 255.255.252.0
After this configuration. ISP-1 and ISP-2 continue to receive the specific routes and the summary route.
Which configuration resolves the issue?
- A . router bgp 64511
aggregate-address 172.16.20.0 255.255.252.0 summary-only - B . router bgp 64511
neighbor 192.168.100.1 summary-only
neighbor 192.168.200.2 summary-only - C . interface E 0/0
ip bgp suppress-map BLOCK_SPECIFIC
!
interface E 0/1
ip bgp suppress-map BLOCK_SPECIFIC
!
ip prefix-list PL_BLOCK_SPECIFIC
permit 172.16.20.0/22 ge 24
!
route-map BLOCK_SPECIFIC permit 10
match ip address prefix-list PL_BLOCK_SPECIFIC - D . ip prefix-list PL_BLOCK_SPECIFIC
deny 172.16.20.0/22 ge 22
ip prefix-list PL BLOCK SPECIFIC
permit 172.16.20.0/22
!
route-map BLOCK_SPECIFIC permit 10
match ip address prefix-list PL_BLOCK_SPECIFIC
!
router bgp 64511
aggregate-address 172.16.20.0 255 255.252.0 suppress-map BLOCKSPECIFIC
A
Explanation:
When the aggregate-address command is used within BGP routing, the aggregated address is advertised, along with the more specific routes. The exception to this rule is through the use of the summary-only command. The “summary-only” keyword suppresses the more specific routes and announces only the summarized route.
What is an MPLS LDP targeted session?
- A . session between neighbors that are connected no more than one hop away
- B . LDP session established between LSRs by exchanging TCP hello packets
- C . label distribution session between non-directly connected neighbors
- D . LDP session established by exchanging multicast hello packets
Refer to the exhibit.

R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns the route to 172.16.25.0/24 from R1, but it does not advertise to R3.
What is the reason the route is not advertised?
- A . R2 does not have a route to the next hop, so R2 does not advertise the prefix to other clients.
- B . Route reflector setup requires full IBGP mesh between the routers.
- C . In route reflector setup, only classful prefixes are advertised to other clients.
- D . In route reflector setups, prefixes are not advertised from one client to another.