Cisco 300-410 Practice Exams
Last updated on Nov 16,2026- Exam Code: 300-410
- Exam Name: Implementing Cisco Enterprise Advanced Routing and Services (ENARSI)
- Certification Provider: Cisco
- Latest update: Nov 16,2026
Refer to the exhibit.

After reloading the router an administrator discovered that the interface utilization graphs displayed inconsistencies with their previous history in the NMS.
Which action prevents this issue from occurring after another router reload in the future?
- A . Rediscover all the router interfaces through SNMP after the router is reloaded
- B . Save the router configuration to startup-config before reloading the router
- C . Configure SNMP to use static OlDs referring to individual router interfaces
- D . Configure SNMP interface index persistence on the router
Refer to the exhibit.

The R1 OSPF neighbor is not receiving type 5 external LSAs for 132.108.2.0/24 and 132.108.3.0/24 networks.
Which configuration command resolves the issue?
- A . access-list 1 permit 132.108.0.0 0.0.1.255
- B . access-list 1 permit 132.108.0.0 0.0.3.255
- C . access-list 1 permit 132.108.2.0 0.0.0.255
- D . access-list 1 permit 132.108.4.0 0.0.3.255
Refer to the exhibit.

An enterprise operations team must monitor all application server traffic in the data center The team finds that traffic coming from the hub site from R3 and R6 rs monitored successfully but traffic destined to the application server is not monitored.
Which action resolves the issue?
A)
![]()
B)
![]()
C)
![]()
D)
![]()
- A . Option A
- B . Option B
- C . Option C
- D . Option D
Refer to the exhibit.

Router ABR-Rtr is not propagating the internet routes in OSPF area 10. which causes internet reachability problems in the area.
Which action resolves the issue?
- A . ABR-Rtr must configure the default-information originate always command.
- B . ABR-Rtr must configure the area 10 stub no-summary command.
- C . ABR-Rtr network type must be broadcast network.
- D . ABR-Rtr must advertise the 0.0.0.0/0 default route in area 10.
A customer reports that traffic is not passing on an EIGRP enabled multipoint interface on a router configured as below:
interface Serial0/0
no ip address
interface Server0/0/0.9 multipoint
ip address 10.1.1.1 255.255.255.248
ip split-horizon eigrp 1
Which action resolves the issue?
- A . Enable poison reverse
- B . Enable split horizon
- C . Disable poison reverse
- D . Disable split horizon
Refer to the exhibit.

A bank ATM site has difficulty connecting with the bank server. A network engineer troubleshoots the issue and finds that R4 has no active route to the bank ATM site.
Which action resolves the issue?
- A . Advertise 10.10.30.0/24 subnet in R1 EIGRP AS.
- B . EIGRP peering between R3 and R4 to be fixed.
- C . EIGRP peering between R1 and R2 to be fixed.
- D . Advertise 10.10.30.0/24 subnet in R3 EIGRP AS.
An engineer configured VRF-Lite on a router for VRF blue and VRF red. OSPF must be enabled on each VRF to peer to a directly connected router in each VRF.
Which configuration forms OSPF neighbors over the network 10.10.10.0/28 for VRF blue and 192.168.0.0/30 for VRF red?

- A . Option A
- B . Option B
- C . Option C
- D . Option D
Refer to the exhibit.

Which action resolves the issue?
- A . Establish connectivity between the NTP server and the switch.
- B . Configure the local time on Cisco DNA Center
- C . Configure the local time on the SW1 device
- D . Establish connectivity between the NTP server and Cisco DNA Center.
Refer to the exhibit.


An engineer is troubleshooting a failed Telnet session from PC to the DHCP server.
Which action resolves the issue?
- A . Remove sequence 30 and add it back to the IPv6 traffic filter as sequence 5.
- B . Remove sequence 20 and add it back to the IPv6 traffic filter as sequence 5.
- C . Remove sequence 10 to add the PC source IP address and add it back as sequence 10.
- D . Remove sequence 20 for sequence 40 in the access list to allow Telnet.
What is the minimum time gap required by the local system before putting a BFD control packet on the wire?
- A . Detect Mult
- B . Required Min Echo RX Interval
- C . Desired Min TX Interval
- D . Required Min RX Interval
C
Explanation:
Desired Min TX Interval: This is the minimum interval, in microseconds, that the local system would like to use when transmitting BFD Control packets, less any jitterapplied. The value zero is reserved.
Required Min Echo RX Interval: This is the minimum interval, in microseconds, between received BFD Echo packets that this system is capable of supporting, less anyjitter applied by the sender. If this value is zero, the transmitting system does not support the receipt of BFD Echo packets.
Reference: https://tools.ietf.org/html/rfc5880