DELL EMC D-PDC-DY-23 Practice Exams
Last updated on Nov 16,2026- Exam Code: D-PDC-DY-23
- Exam Name: Dell PowerSwitch Data Center Deploy 2023
- Certification Provider: DELL EMC
- Latest update: Nov 16,2026
A network administrator is designing a Layer 2 topology and requires separate spanning- tree roots to avoid having a given port blocked for all instances.
Which spanning-tree protocols will meet this need?
- A . STP & RSTP
- B . RSTP-PV & MSTP
- C . STP & RSTP-PV
- D . RSTP & MSTP
Which Ethernet interface speeds do Dell Networking OS10 switches support?
- A . 10, 16, and 40Gb
- B . 1, 10, and 25Gb
- C . 1, 2, and 100Gb
- D . 4, 8, and 32Gb
When using Policy-Based Routing, what is a valid action?
- A . Set source IP address
- B . Drop packet
- C . Set destination TCP port number
- D . Set 802.1Q VLAN ID
What is the default PIM-SSM IP range?
- A . 224.0.0.0/4
- B . 224.0.0.0/24
- C . 232.0.0.0/8
- D . 232.0.0.0/4
When configuring a vrf instance for the management interface that has been in use, what step must be done first to configure it?
- A . Configure a management route
- B . Remove the default route
- C . Remove all configured settings
- D . Configure an IP Address
A network administrator has to configure a virtual IP address using VRRP on interface VLAN 100 within OS10.
What are the correct steps to accomplish this?
- A . OS10(config)# interface vlan 100
OS10(conf-if-vl-100)# ip address 10.0.100.2/24
OS10(conf-if-vl-100)# vrrp-group 256
OS10(conf-vlan100-vrid-256)# virtual-address 10.0.100.1 - B . OS10(config)# interface vlan 100
OS10(conf-if-vl-100)# ip address 10.0.100.2/24
OS10(conf-if-vl-100)# standby-group 250
OS10(conf-vlan100-vrid-250)# virtual-address 10.0.100.1 - C . OS10(config)# interface vlan 100
OS10(conf-if-vl-100)# ip address 10.0.100.1/24
OS10(conf-if-vl-100)# vrrp-group 250
OS10(conf-vlan100-vrid-250)# virtual-address 10.0.100.2 - D . OS10(config)# interface vlan 100
OS10(conf-if-vl-100)# ip address 10.0.100.1/24
OS10(conf-if-vl-100)# standby-group 256
OS10(conf-vlan100-vrid-256)# standby-address 10.0.100.2
Refer to the exhibit.

No static routing has been configured. For iBGP loopback-based peering, which statement is correct?
- A . It is not necessary for the routing table on S1 to have an entry for the loopback network of S3.
- B . S1 should have the Loopback network of S3 in its routing table for loopback-based peering.
- C . For iBGP peering, physical interface addresses must be used.
- D . A static route on S1 to 144.254.32.1/32 will eliminate the need for loopback-based peering with S3.
With what feature is the downstream ethernet 1/1/9:1-1/1/9:4 command associated?
- A . Downlink Failure Detection
- B . Uplink Failure Detection
- C . Unidirectional Forwarding Detection
- D . Bidirectional Forwarding Detection
A network administrator wants to limit the amount of bandwidth that video traffic can consume.
Which type of policy map should be used?
- A . Queuing
- B . It is not possible to limit bandwidth using policy maps
- C . Control plane
- D . Application
Refer to the exhibit:

From S1, a ping to the host address of 192.168.37.3 is not successful. The routing table on S1 shows three directly connected networks (including the Lo0 network of S1). Network 192.168.34.0/24 and the Lo0 networks of S2 and S3 are the only OSPF-learned networks in the routing table. The system on the 192.168.37.0/24 network can ping S3.
Which command offers a solution to the inability to ping the host address from S1?
- A . S1(config-router-ospf-1)# ip route 192.168.37.0/24 interface null 0
- B . S3(config-router-ospf-1)# update-source loopback 0
- C . S3(config-router-ospf-1)# redistribute connected
- D . S1(config-router-ospf-1)# network 192.168.37.0/24